Philips DVP3560/12 Manual De Usuario
19
9 Troubleshooting
Warning
Risk of electric shock. Never remove the casing of the
•
product.
To keep the warranty valid, never try to repair the
product yourself.
If you have problems using this product, check the
following points before you request service. If you
still have a problem, register your product and get
support at www.philips.com/welcome.
product yourself.
If you have problems using this product, check the
following points before you request service. If you
still have a problem, register your product and get
support at www.philips.com/welcome.
If you contact Philips, you will be asked for the model
and serial number of your product. The model
number and serial number are on the back of your
product. Write the numbers here:
and serial number of your product. The model
number and serial number are on the back of your
product. Write the numbers here:
Model No. __________________________
Serial No. ___________________________
Main unit
The buttons on this unit do not work.
Disconnect this product from the power
•
outlet for a few minutes, then connect again.
No reaction to the remote control.
Connect this product to the power outlet.
•
Point the remote control at the IR sensor
•
located on the front panel of this product.
Insert the batteries correctly.
Insert the batteries correctly.
•
Insert new batteries in the remote control.
•
Picture
No picture.
See the TVs user manual on how to select
•
the correct input on the TV. Change the TV
channel until you see the Philips screen.
If you have turned on the progressive scan
channel until you see the Philips screen.
If you have turned on the progressive scan
•
setting or change the TV system setting,
switch back to default mode: 1) Press to
open the disc compartment. 2) Press the
Numeric button ‘1’ (for progressive scan) or
the Numeric button’3’ (for TV system).
switch back to default mode: 1) Press to
open the disc compartment. 2) Press the
Numeric button ‘1’ (for progressive scan) or
the Numeric button’3’ (for TV system).
No picture on HDMI connection.
If this product is connected to an unauthorized
•
display device with an HDMI cable, the audio/
video signal may not be output.
Check if the HDMI cable is faulty. Replace a
video signal may not be output.
Check if the HDMI cable is faulty. Replace a
•
new HDMI cable.
If this happens when you change the HDMI
If this happens when you change the HDMI
•
video resolution, you have to switch to its
default mode: 1) Press to open the disc
compartment. 2) Press the numeric button “1”.
default mode: 1) Press to open the disc
compartment. 2) Press the numeric button “1”.
Specifications
Note
Specification and design are subject to change without
•
notice
USB
Compatibility: Hi-Speed USB (2.0)
•
Class support: UMS (USB Mass Storage Class)
•
Video
Video
Signal system: PAL / NTSC
•
Composite video output: 1 Vpp ~ 75 ohm
•
Component video output: 0.7 Vpp ~ 75 ohm
•
HDMI output: 480i, 480p, 576i, 576p, 720p,
•
1080i, 1080p
Scart: Euroconnector
Scart: Euroconnector
•
Audio
Audio
Analog stereo output
•
Signal to noise ratio (1 kHz): > 100 dB
•
(A-weighted)
Dynamic Range (1 kHz): > 90 dB (A-weighted)
Dynamic Range (1 kHz): > 90 dB (A-weighted)
•
Crosstalk (1 kHz): > 100 dB
•
Distortion/noise: (1 kHz): > 85 dB
•
MPEG MP3: MPEG Audio L3
•
Scart output
•
Digital output
•
Coaxial
•
HDMI output
HDMI output
•
Main unit
Main unit
Dimensions (w x h x d): 360 x 39 x 209 (mm)
•
Net Weight: 1.2 kg
•
Power
Power
Power supply rating: 230 V; 50 Hz
•
Power consumption: < 10 W
•
Power consumption in standby mode: < 0.45 W
•
Accessories supplied
Accessories supplied
Remote control and batteries
•
User Manual
•
Quick Start Guide
•
Laser specification
Laser specification
Type: Semiconductor laser InGaAIP (DVD),
•
AIGaAs (CD)
Wave length: 658 nm (DVD), 790 nm (CD)
Wave length: 658 nm (DVD), 790 nm (CD)
•
Output Power: 7.0 mW (DVD), 10.0 mW
•
(VCD/CD)
Beam divergence: 60 degrees
Beam divergence: 60 degrees
•
English
EN