Mitsubishi WD-65738 Guía Del Usuario
1. Basic Setup and Operation
7
For assistance call 1(800) 332-2119
The STATUS Indicator
Key
Off
Steady On
Slow Blinking
Fast Blinking
LED Color TV Condition
None
TV is powered off. Normal operation.
Green
TV is powered on. Normal operation.
Green
TV powered off, auto-on TV Timer is
set.
Normal operation. TV can be turned on
at any time.
set.
Normal operation. TV can be turned on
at any time.
Green
TV just powered off and lamp is
cooling.
Sixty seconds after turning off TV, LED
will start to blink. TV can be turned back
on before blinking starts or after blink-
ing stops, but not while the indicator is
blinking. Normal operation.
cooling.
Sixty seconds after turning off TV, LED
will start to blink. TV can be turned back
on before blinking starts or after blink-
ing stops, but not while the indicator is
blinking. Normal operation.
Yellow
TV is too hot. The TV will display a
warning message and shut off if it over-
heats.
• Ambient room temperature may be
warning message and shut off if it over-
heats.
• Ambient room temperature may be
too high. Turn off the TV and let the
room temperature drop.
room temperature drop.
• Clear blocked air vents. Ensure at
least a four-inch clearance on all
sides of the TV.
sides of the TV.
Yellow
Lamp access door is not secure or no
lamp installed.
TV will not operate until lamp access
door is secured. See Appendix A.
lamp installed.
TV will not operate until lamp access
door is secured. See Appendix A.
Red
Lamp failure. Replace the lamp. See
Appendix A.
Appendix A.
Red/
Yellow
Yellow
TV may require service.
Hold power button on front panel for
•
10 seconds to reset TV.
If LED continues to flash red and
If LED continues to flash red and
•
yellow after reset, turn off the TV and
unplug it from the AC power source.
Wait one minute and then plug the
set back in.
If LED continues to flash red and
unplug it from the AC power source.
Wait one minute and then plug the
set back in.
If LED continues to flash red and
•
yellow, go to www.mitsubishi-tv.com
or call 1-800-332-2119 to receive
Authorized Service Center informa-
tion.
You may be asked to count how
many times the LED flashes each
color to aid in troubleshooting.
or call 1-800-332-2119 to receive
Authorized Service Center informa-
tion.
You may be asked to count how
many times the LED flashes each
color to aid in troubleshooting.
Using the ANT (Antenna) Input
If using an antenna or direct cable service (no cable
box), connect the incoming coaxial cable to the TV’s
ANT input. Refer to page 12.
box), connect the incoming coaxial cable to the TV’s
ANT input. Refer to page 12.
You must perform a channel scan to enable recep-
tion of digital channels. If you skip this step, the TV
will receive only analog channels. The channel scan
will search for high-definition and standard-definition
channels available in the local area.
tion of digital channels. If you skip this step, the TV
will receive only analog channels. The channel scan
will search for high-definition and standard-definition
channels available in the local area.
Memorizing Channels with Channel Scan
For the ANT input
For the ANT input
To start channel memorization
Power on the TV.
1.
Press
2.
MENU and open the Setup > Channel menu.
First press to navigate to the Setup icon, then
use to highlight the Channel icon.
use to highlight the Channel icon.
Start channel memorization from the Setup > Channel
menu.
menu.
Press
3.
to enter the menu.
Highlight
4.
Ant Air if connected to an
over-the-air antenna. Highlight
Ant
Cable for service over direct cable
(no cable box). Press
(no cable box). Press
ENTER to add a
check.
For first-time setup, highlight
For first-time setup, highlight
5.
All
channels. To scan for channels not
already in memory, highlight
already in memory, highlight
New
only. Press ENTER to add a check.
Highlight
Highlight
6.
Scan and press ENTER.
Channel memorization may take up
to 15 minutes to complete.
to 15 minutes to complete.
To stop channel memorization before completion,
press CANCEL.
press CANCEL.
Setting Up and Using TV Inputs