Mitsubishi WS-55517 Manual De Usuario
14
AV
Receiver
TV
Device to be
connected
stereo and/or digital
audio cables
video and stereo
audio cables
stereo and digital audio cables
IR Emitters
Connecting External Devices & NetCommand
®
Setup
NetCommand is able to control many current audio and video devices by sending remote control signals from the
TV to each device through IR emitters. Additionally, it is able to learn the remote control signals used by most audio
video devices not already in the TV’s memory. NetCommand can automatically switch the TV along with compatible
or learned Audio/Video (A/V) Receivers to the correct input for use with each device. It is important that the inputs
on the TV and A/V Receiver back panel match the NetCommand setup that is displayed on-screen.
or learned Audio/Video (A/V) Receivers to the correct input for use with each device. It is important that the inputs
on the TV and A/V Receiver back panel match the NetCommand setup that is displayed on-screen.
To simplify the installation of NetCommand, there is a step-by-step on-screen NetCommand setup procedure in this
chapter, which details the type and brand of devices you are connecting to the TV. The NetCommand Setup also
assigns preset TV and A/V Receiver inputs for each device. You should connect each device to the TV input (both
audio and video) and to the A/V Receiver (audio) as shown in the figure below.
assigns preset TV and A/V Receiver inputs for each device. You should connect each device to the TV input (both
audio and video) and to the A/V Receiver (audio) as shown in the figure below.
After using NetCommand Setup, you may go to the NetCommand menu (see “Edit NetCommand”) at any time
to change the inputs you used for connecting each device, custom name devices, add devices not included in
the presets above or delete devices no longer used. See Connection Helpful Hints, at the end of this chapter for
additional information on device setup.
the presets above or delete devices no longer used. See Connection Helpful Hints, at the end of this chapter for
additional information on device setup.
The following charts show which preset inputs you should use on the TV and A/V Receiver.
Chart
1
shows
TV
inputs.
Chart 2 shows the A/V Receiver inputs used by A/V Receiver models already known by NetCommand.
Model
M-VR800 &
M-VR1000
Model
M-VR900 &
M-VR700
Model
Lifestyle ® 28
Model
AVR-2700
Model
DTR-9.1
Model
VR-2080
Model
SR8200
Model
VSX-D557
Model
VSX-49TX
Model
RSX-1065
Model
STR-DE825
Model
RV-X2095
Model
RX-V2200
Device Audio Output
to
AV Receiver Inputs by Name
VCR
VCR 1
VCR
VCR
VCR-1
Video 1
Video 1
VCR1
VCR/Tape VCR 1/DVR
Video 2
Video 1
VCR 1
VCR 1
Satellite Receiver
Aux
Cable/DBS
AUX
CD
Video 3
Video 3
DSS
CD
SAT
Video 4
TV/DBS
TV/DBS
D-TV/LD
DVD Player
DVD
DVD
(built-in)
DVDVDP
DVD
Video 4
DVD
LD/SAT
DVD/LD
Video 5
TAPE/MD
CD
DVD
TV Monitor Output
(& Digital Audio)
(& Digital Audio)
TV
TV
TV
TV/DBS
Video 4
Video 4
TV
DVD/TV
TV
Video 1
DVD/LD
DVD/LD
CBL/SAT
Chart 2
Mitsubishi 1 Mitsubishi 2
Bose
Denon
Integra
Kenwood Marantz
Pioneer 1
Pioneer 2
Rotel
Sony
Yamaha 1 Yamaha 2
Chart 1
Device Audio and Video Outputs to TV Inputs
Cable for CableCARD™ Service
ANT-1
Antenna/Cable (digital/analog)
ANT-1 if primary viewing source,
ANT-2 if secondary viewing source
ANT-2 if secondary viewing source
Cable box
ANT-2
VCR
Input-1
Satellite Receiver (DBS)
Input-2
Camcorder
Input-3 (on front panel)
DVD Player
Component-1