KitchenAid ksso36qmx Manual De Usuario
![KitchenAid](https://files.manualsbrain.com/attachments/3d34882145cc792176ac4280be3df6ce39b27869/common/fit/150/50/747ee6e29a14dad568348edacc16f5166992002567b60a7cd75e7e2a9071/brand_logo.png)
15
Refrigerator
Side Trim
Inset Installation Dimensions
1. Measure the distance from point A (as shown) to the back
wall. Add
¹⁄₃₂" (0.8 mm) to this measurement to allow the side
panel to fit into the trim.
2. If the panel is more than
³⁄₈" (9.5 mm) thick, rout the front
edge to allow the side panel to fit into the trim.
Recessed Inset Installation Dimensions
1. Measure the distance from point A (as shown) to back wall.
2. Rout the front edge of the support board or attach a
³⁄₈"
(9.5 mm) board to hold the panel in the cabinet side trim.
INSTALLATION
REQUIREMENTS
Tools and Parts
IMPORTANT:
■
Installer: Leave Installation Instructions with the homeowner.
■
Homeowner: Keep Installation Instructions for future
reference. Save these Installation Instructions for the local
electrical inspector’s use.
reference. Save these Installation Instructions for the local
electrical inspector’s use.
TOOLS NEEDED:
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Read and follow the instructions provided with any tools listed
here.
PARTS NEEDED:
■
Six #8 x 3" (7.6 cm) wood screws (longer screws may be needed)
■
One or two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s)
■
Order factory panels, make custom panels or consult a
qualified cabinetmaker or carpenter to make the panels.
qualified cabinetmaker or carpenter to make the panels.
Classic Series: Order factory panels, make custom panels, or
consult a qualified cabinetmaker or carpenter to make the
panels. See “Design Specifications” for more information.
consult a qualified cabinetmaker or carpenter to make the
panels. See “Design Specifications” for more information.
Overlay Series: Make custom panels, or consult a qualified
cabinetmaker or carpenter to make the panels. See “Design
Specifications” for more information.
cabinetmaker or carpenter to make the panels. See “Design
Specifications” for more information.
Pro Line
®
, Complete and Architect
®
Series are shipped
complete.
■
If you are connecting the water line directly to copper tubing
and not to a shutoff valve, you need a ferrule, a union, and a
and not to a shutoff valve, you need a ferrule, a union, and a
¹⁄₄" (6.35 mm) compression fitting.
23
³⁄₈
"
(59.40 cm)
Overlay
³⁄₁₆
"
(4.5 mm)
³⁄₈
"
(9.7 mm)
¹⁄₁₆
"
(1.5 mm)
¹⁄₈
"
(3.2 mm)
A
■
Hand drill or electric drill
(properly grounded)
(properly grounded)
■
Torx
®
†
T27 screwdriver
■
Drill bits
■
¹¹⁄₃₂" nut driver
■
Two adjustable wrenches
■
³⁄₈" and ¹⁄₂" open-end
wrenches
wrenches
■
Phillips screwdriver
■
⁵⁄₃₂" Allen wrench
■
Small level
■
⁵⁄₁₆" socket wrench
■
Appliance dolly
■
Tape measure
A
†®TORX is a registered trademark of Textron Innovations Inc.