LG 19LE5300 Manual De Propietario

156

APPENDIX

11. Sharpness (Command: k k)
To adjust screen sharpness.
You can also adjust sharpness in the Picture menu.

Transmission [k][k][ ][Set ID][ ][Data][Cr]

Data Min: 00 - Max: 64 (*transmit by Hexadecimal code)
*Refer to ‘Real data mapping’.

Acknowledgement [k][ ][Set ID][ ][OK/NG][Data][x]

12. OSD Select (Command: k l)
To select OSD (On Screen Display) on/off.

Transmission

[k][l][ ][Set ID][ ][Data][Cr]

Data 00: OSD off

Data 01: OSD on

Acknowledgement [l][ ][Set ID][ ][OK/NG][Data][x]

13. Remote Control Lock Mode (Command: k m)
To lock the remote control and the front panel con-

trols on the set.

Transmission

[k][m][ ][Set ID][ ][Data][Cr]

Data 00: Lock off

Data 01: Lock on

Acknowledgement [m][ ][Set ID][ ][OK/NG][Data][x]

If you’re not using the remote control and front panel

controls on the TV, use this mode. When main power

is on/off, remote control lock is released.

If Key Lock is on in the standby mode, TV will not turn

on by POWER button of remote control and on the

TV.

14. Treble (Command: k r)
To adjust treble.

You can also adjust treble in the Audio menu.

Transmission [k][r][ ][Set ID][ ][Data][Cr]

Data Min: 00 - Max: 64 (*transmit by Hexadecimal code)

*Refer to ‘Real data mapping’.

Acknowledgement

[r][ ][Set ID][ ][OK/NG][Data][x]

15. Bass (Command: k s)
To adjust bass.

You can also adjust bass in the Audio menu.

Transmission [k][s][ ][Set ID][ ][Data][Cr]

Data Min: 00 - Max: 64 (*transmit by Hexadecimal code)

*Refer to ‘Real data mapping’.

Acknowledgement

[s][ ][Set ID][ ][OK/NG][Data][x]

16. Balance (Command: k t)
To adjust balance.

You can also adjust balance in the Audio menu.

Transmission [k][t][ ][Set ID][ ][Data][Cr]

Data Min: 00 - Max: 64 (*transmit by Hexadecimal code)

*Refer to ‘Real data mapping’.

Acknowledgement

[t][ ][Set ID][ ][OK/NG][Data][x]

17. Color Temperature (Command: x u)
To adjust color temperature.

You can also adjust color temperature in the Picture

menu.

Transmission [x][u][ ][Set ID][ ][Data][Cr]

Data Min: 00 - Max: 64 (*transmit by Hexadecimal code)
*Refer to ‘Real data mapping’.

Acknowledgement

[u][ ][Set ID][ ][OK/NG][Data][x]

18. Energy Saving (Command: j q)
To control the energy saving function.

Transmission [ j ][q][ ][Set ID][ ][Data][Cr]

  Data 00: Energy saving - off
          01: Energy saving - Minimum
          02: Energy saving - Medium
          03: Energy saving - Maximum
           04: Energy saving - Auto (depending on model)
          05: Energy saving - Screen off

Acknowledgement [q][ ][Set ID][ ][OK/NG][Data][x]

19. Auto Configuration (Command: j u)
To adjust picture position and minimize image shak-

ing automatically. Auto configuration only works in

RGB-PC mode.

Transmission [ j ][u][ ][Set ID][ ][Data][Cr]

Data 01: To set

Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]

20. Channel Tuning (Command: m a)
To tune channel to following physical/major/minor number.

  Transmission [m][a][ ][Set ID][ ][Data00][ ][Data01]
  [ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]

Digital channels have a Physical, Major, and Minor

channel number. The Physical number is the actual

digital channel number, the Major is the number that

the channel should be mapped to, and the Minor is

the sub-channel. Since the ATSC tuner automatically

maps the channel to the Major number, the Physical

number is not required when sending a command.

  Data 00:  Physical Channel Number
              NTSC air: 02 - 45, NTSC cable: 01, 0E - 7D
              ATSC air: 01 - 45, ATSC cable: 01 - 87
  Data 01 & 02:  Major Channel Number
  Data 01: High byte                    Data 02: Low byte
        Two  bytes  are  available  for  the  Major  and  Minor,

normally only the second byte is used.

Data 03 & 04: Minor Channel Number
Not needed for NTSC.