Craftsman 12004 Manual De Usuario
10
Emptying the Collection Tank
Installing & Cleaning the Supplied Cartridge Filter
Maintenance
1. Verify that the power cord is
disconnected from the outlet. (Fig. 1)
2. Disconnect the hose from the vacuum.
(Fig. 2)
3. Undo the latches and remove the power
head from the collection tank. (Fig. 3)
Place power head on a soft, clean
surface upside down.
4. Clear all dirt or debris from the collection
tank and hose into a proper waste
container. (Fig. 4)
5. Clean or replace the fi lters.
6. Check the hose, attachments, and
power cord to verify that they have not
been damaged.
disconnected from the outlet. (Fig. 1)
2. Disconnect the hose from the vacuum.
(Fig. 2)
3. Undo the latches and remove the power
head from the collection tank. (Fig. 3)
Place power head on a soft, clean
surface upside down.
4. Clear all dirt or debris from the collection
tank and hose into a proper waste
container. (Fig. 4)
5. Clean or replace the fi lters.
6. Check the hose, attachments, and
power cord to verify that they have not
been damaged.
Installing Cartridge Filter
1. Verify that the power cord is
disconnected from the outlet. (Fig. 1)
2. Undo the latches and remove the
power head from the collection tank.
3. Place power head on a clean surface in
upside down position.
4. Slide the cartridge fi lter over the fi lter
cage. (Fig. 2) Carefully push fi lter down
until it is fully seated on the power head.
(Fig. 3)
5. To secure fi lter; put on retainer nut and
turn clockwise to tighten until snug. Do
not over tighten. (Fig. 4)
1. Verify that the power cord is
disconnected from the outlet. (Fig. 1)
2. Undo the latches and remove the
power head from the collection tank.
3. Place power head on a clean surface in
upside down position.
4. Slide the cartridge fi lter over the fi lter
cage. (Fig. 2) Carefully push fi lter down
until it is fully seated on the power head.
(Fig. 3)
5. To secure fi lter; put on retainer nut and
turn clockwise to tighten until snug. Do
not over tighten. (Fig. 4)
Removing and Cleaning Cartridge Filter
1. Position power head in the upside down
position. If the retainer nut was used to
secure the fi lter, remove retainer nut by
turning counter clockwise.
2. Carefully lift fi lter up from fi lter cage.
(Fig. 5)
1. Position power head in the upside down
position. If the retainer nut was used to
secure the fi lter, remove retainer nut by
turning counter clockwise.
2. Carefully lift fi lter up from fi lter cage.
(Fig. 5)
NOTE: For best cartridge fi lter cleaning
results, cleaning should be conducted
outdoors and not indoors.
results, cleaning should be conducted
outdoors and not indoors.
3. To clean a dry cartridge fi lter after it has
been removed, gently tap it against the
inside wall of the container or brush the
dirt off. Debris will begin to break up,
loosen and fall.
been removed, gently tap it against the
inside wall of the container or brush the
dirt off. Debris will begin to break up,
loosen and fall.
NOTICE! The fi lter included is made of
high quality material designed to stop small
dust particles. The fi lter should be used for
dry pick-up only. A dry fi lter is necessary
to pick up dust. If the dust fi lter is wet, it
will clog quickly and be very diffi cult to
clean. Handle the fi lter carefully when
removing it for cleaning and replacing it.
Check the fi lters for tears or small holes; a
small hole can let dust pass through and
out of the cleaner. Do not use a fi lter with
holes or tears; replace it immediately.
high quality material designed to stop small
dust particles. The fi lter should be used for
dry pick-up only. A dry fi lter is necessary
to pick up dust. If the dust fi lter is wet, it
will clog quickly and be very diffi cult to
clean. Handle the fi lter carefully when
removing it for cleaning and replacing it.
Check the fi lters for tears or small holes; a
small hole can let dust pass through and
out of the cleaner. Do not use a fi lter with
holes or tears; replace it immediately.
1
2
3
4
5
1
3
4
2
7. Place power head on collection tank and
secure latches.
secure latches.