Edelbrock 15621 Manual De Usuario

©2009 Edelbrock Corporation

Brochure #63-1551

Page 3

Edelbrock E-Force Supercharger Kits
Rev. 3/09 - AJ/mc

❑ 1 Supercharger/Manifold Top Plate Assembly

❑ 1 Supercharger Intake Manifold

❑ 1 Supercharger Snout Support/Idler Pulley Bracket

❑ 1 Alternator Support Bracket

❑ 1 Idler Pulley

❑ 1 Idler Pulley Spacer

❑ 1 Idler Pulley Nut

❑ 1 Crankshaft Supercharger Drive Pulley

❑ 3 Crankshaft Pulley Shim

❑ 1 7/16-20 x 2.75” Long, 1.50” Shoulder Bolt (Crankshaft Balancer)

❑ 3 3/8-24 x 3.75” Long, 2.625” Shoulder Bolt (Crankshaft Pulley)

❑ 3 3/8-16 x 4” Long, 2.75” Shoulder Bolt (Idler Pulley and Bracket)

❑ 10 3/8-16 x 1.25” Long Bolt (Intake Manifold)

Standard Bolt Pattern Kits Only

❑ 2 3/8-16 x 1.75” Long, .625” Shoulder Bolt (Intake Manifold)

Standard Bolt Pattern Kits Only

❑ 4 5/16-18 x 1.75” Long Bolt (Intake Manifold)

Vortec/E-Tec Bolt Pattern Kits Only

❑ 4 5/16-18 x 2.5” Long Bolt (Intake Manifold)

Vortec/E-Tec Bolt Pattern Kits Only

❑ 8 1/4-20 x 1” Long Bolt (Manifold Top Plate to Intake Manifold)

❑ 4 5/16-18 x 1” Long Bolt (Manifold Top Plate to Intake Manifold)

Standard Bolt Pattern Kits Only

❑ 3 3/8” I.D. Split-Lock Washer

❑ 1 7/16” I.D. Split-Lock Washer

❑ 1 7/16” I.D. x .120 Thick Flat Washer

❑ 1 Supercharger Drive Belt

❑ 1 Intake Manifold O-Ring Seal (54” Long)

❑ 1 Intake Manifold Gaskets (Pair)

❑ 1 Carburetor Kit (800CFM Thunder Series AVS, Electric Choke)**

❑ 1 Carburetor Stud, Nut, & Washer Kit**

Carburetor and associated hardware included in certain kits ONLY.

See “Applications” section for those kits that include carburetor.

❑ 1 Supercharger/Manifold Top Plate Assembly

❑ 1 Supercharger Intake Manifold

❑ 10 3/8-16 x 1.25” Long Bolt (Intake Manifold)

Standard Bolt Pattern Kits Only

❑ 2 3/8-16 x 1.75” Long, .625” Shoulder Bolt (Intake Manifold)

Standard Bolt Pattern Kits Only

❑ 4 5/16-18 x 1.75” Long Bolt (Intake Manifold)

Vortec/E-Tec Bolt Pattern Kits Only

❑ 4 5/16-18 x 2.5” Long Bolt (Intake Manifold)

Vortec/E-Tec Bolt Pattern Kits Only

❑ 8 1/4-20 x 1” Long Bolt (Manifold Top Plate to Intake Manifold)

❑ 4 5/16-18 x 1” Long Bolt (Manifold Top Plate to Intake Manifold)

Standard Bolt Pattern Kits Only

❑ 1 Intake Manifold O-Ring Seal (54” Long)

❑ 1 Intake Manifold Gaskets (Pair)

❑ 1 Carburetor Kit (800CFM Thunder Series AVS, Electric Choke)**

❑ 1 Carburetor Stud, Nut, & Washer Kit**

Carburetor and associated hardware included in certain kits ONLY.

See “Applications” section for those kits that include carburetor.

❑ Box and open end wrenches
❑ Socket set
❑ Distributor wrench
❑ Pliers (channel locks and hose clamp)
❑ Screw drivers (regular and Phillips)
❑ Torque wrench
❑ Hammer
❑ Gasket scraper or putty knife
❑ Timing light
❑ Vacuum gauge
❑ Rags
❑ Water bucket
❑ Paper and pencil

❑ Gaskets-Edelbrock, or performance gasket equivalent
❑ Pipe plugs, if needed
❑ Edelbrock Gasgacinch (#9300)
❑ RTV High Temp silicone sealer or O/2 sensor safe RTV
❑ Masking tape
❑ Modeling clay or putty
❑ Chalk
❑ Radiator coolant
❑ Teflon thread tape or PST thread sealer or equivalent
❑ Thread locking compound such as Loctite™ (Red, Blue, or

equivalent)

❑ Supercharger & Accessory drive belt (for Billet Specialties

applications, see installation procedure for recommended part
numbers)

IMPORTANT NOTE: Edelbrock E-Force Supercharger kits do not include
the Billet Specialties Tru Trac Pulley System. These systems are available
seperately from Edelbrock and include a water pump, A/C compressor,
drive belt, alternator, and all the pulleys, brackets, and mounting
hardware necessary for a complete installation. These systems can be
purchased with a power steering pump as part #1565, or without as part
#1566.