Casio WV200A-1AV Manual De Usuario

1

MA08

10-EA

 Congratulations upon your selection of this CASIO watch. To get the most out of your 
purchase, be sure to read this manual carefully. 

  •  This watch does not have a time zone that corresponds to the UTC offset of 

 Caution! 
 Your watch is shipped with its Auto Display feature (which continually changes the 
contents of the digital display) turned on. Calibration signal reception is disabled while 
Auto Display is turned on.
Press any button to turn off Auto Display and return to the Timekeeping Mode. 

  •  Button operations are indicated using the letters shown 

in the illustration. 

  •  Each section of this manual provides you with the 

information you need in order to perform operations in 
each mode. Further details and technical information 
can be found in the “Reference” section. 

  •  Press  C  to change from mode to mode. 

  •  In any mode (except when a setting screen is on the display), press  B  to illuminate 

the display. 

Press

.

 This watch receives a time calibration signal and updates 
its time setting accordingly. 

  •  Supported time calibration signals: United States (Fort 

Collins), England (Anthorn). 

  •  See the information under “Signal Reception 

Troubleshooting” if you experience problems with time 
calibration signal reception. 

 Current Time Setting 
 This watch adjusts its time setting automatically in 
accordance with a time calibration signal. You can also 
perform a manual procedure to set the time and date, 
when necessary. 

  •   The fi rst thing you should do after purchasing this 

 
  •  When using the watch outside the areas covered by the time signal transmitters, you 

will have to adjust the current time setting manually as required. See “Timekeeping” 
for more information about manual time settings. 

  •  The U.S. time calibration signal can be picked up by the watch while in North 

America. The term “North America” in this manual refers to the area that consists of 
Canada, the continental United States, and Mexico. 

 1. In the Timekeeping Mode, hold down  

A  until the city 

code starts to fl ash, which indicates the setting screen. 

 2. Press  

D (east) and  B (west) to select the city code you 

want to use as your Home City. 

  •  Time calibration signal reception is supported when 

any one of the city codes shown in the table below is 
selected as your Home City. 

 

Honolulu

YWG Winnipeg

Lisbon

Athens

Anchorage

Chicago

London

MOW Moscow

Vancouver

Miami

Madrid

Los Angeles YTO

Toronto

Paris

Edmonton

New York

Rome

Denver

Halifax

Berlin

Mexico City

St. Johns

Stockholm

 

 3. Press  

A  twice to exit the setting screen. 

 Important! 
  •  Normally, your watch should show the correct time as soon as you select your Home 

City code. If it does not, it should adjust automatically after the next auto receive 
operation (in the middle of the night). You can also perform manual receive or you 
can set the time manually. 

  •  The watch will receive the time calibration signal automatically from the applicable 

transmitter (in the middle of the night) and update its settings accordingly. For 
information about the relationship between city codes and transmitters, see “Home 
City Codes and Transmitters”. 

  •  Under factory default settings, auto receive is turned off for all of the following city 

codes:  HNL  (Honolulu),  ANC  (Anchorage),  ATH  (Athens), and  MOW  (Moscow). For 
details about turning on auto receive for these city codes, see “To turn auto receive 
on and off”. 

  •  You can disable time signal reception, if you want. See “To turn auto receive on and 

off” for more information. 

  •  See the maps under “Approximate Reception Ranges” for information about the 

reception ranges of the watch. 

    •  If you are in an area that does not use Daylight Saving Time (summertime), turn off 

the DST setting. 

 Time Calibration Signal Reception 
 There are two different methods you can use to receive the time calibration signal: 
auto receive and manual receive. 
  •  Auto Receive 

 With auto receive, the watch receives the time calibration signal automatically up to 
six times a day. When any auto receive is successful, the remaining auto receive 
operations are not performed. For more information, see “About Auto Receive”. 

  •  Manual Receive 

 Manual receive lets you start a time calibration receive operation with the press of a 
button. For more information, see “To perform manual receive”.