GE Lighting WIZ100 Manual De Usuario

Wireless Integrated Zigbee Sensor

•  Turn power off before inspection, installation or removal

•  Follow all relevant IEC or UL instructions and local building codes

In case of Digital bus miswiring mains can present on 

the device. Make sure all electricity switched of before 

inspection.

Read these instructions completely and 

carefully.

To ensure the product warranty is valid, please ensure all installation instructions and environmental conditions for storage and operation are 

complied with.

Only  GE trained contractors can install the product. 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful 

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

  Operation is subject to the following two conditions:  

• This device may not cause harmful interference, and  

• This device must accept any interference received, including interference that may cause undesired operation.

Cet appareil est conforme aux normes RSS exemptées de licence de Industrie Canada.  

Son fonctionnement est soumis aux deux conditions suivantes:

• Cet appareil ne doit pas provoquer d'interférences et  

• Cet appareil doit accepter toute interférence, y compris celles pouvant causer un mauvais fonctionnement de l'appareil.

To satisfy FCC/ISED RF exposure requirements a separation distance of 20 cm or more must be maintained between the antenna of this device 

and persons during operation. Operation at closer than 20cm is not permitted

Pour être conforme aux limites d’exposition aux ondes RF des normes FCC/ISED, une distance de séparation d’au moins 20 cm doit être main-

tenue entre l’antenne de cet appareil et toute personne pendant son opération.  Mettre en opération cet appareil a une distance plus rappro-

chée que 20 cm n’est pas permis.

Zigbee

95039263

WIZ100

max. 22.5V, class 2, capable of no greater than 15VA power

FCC ID: PUU-WIZ100

IC: 10798A-PUUWIZ100

D31mm x H37.5mm(without antenna)
12.8g
Max 8mA(without digital communication)@Max 22.5V class 2

Passive infrared(PIR) sensor(for motion) light sensor
0℃ to 50℃(Indoor)
Network LED:Network joined
Cable connection to interface module
Easy screw installation to a D22mm hole
3m
5 years

WIZ100

2.1m

2.1m

Minor motion

3m

3m

Major motion

展开尺寸：420*290mm

The Wireless Integrated Zigbee sensor (WIZ100) is a small-size, 

luminaire-integrated sensor with wireless communication, using 

the zigbee protocol. This guarantees a secure and reliable 

communication between the luminaires in the room. Using the 

WIZ100 sensor in each luminaire provides a centralized lighting 

control based on the built-in motion sensing and daylight 

harvesting functionalities. This sensed information is uploaded to 

Daintree network. The control of the luminaire is carried out 

through the digital bus between the output of the sensor and the 

control input of the luminaire’s LED driver. The digital bus also 

provides the necessary supply power for the sensor,

Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could 

void the user's authority to operate the equipment. 

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the 

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This 

equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, 

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a 

particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined 

by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following 

measures: 

—Reorient or relocate the receiving antenna. 

—Increase the separation between the equipment and receiver. 

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  

—Consult the dealer or an experienced radio/TV technician for help

no any additional wiring and auxiliary power supply is required. 

This wireless communication help minimizing the installation 

costs. Besides the automatic operation of the system it is also 

possible to adjust preferred dimming levels through Current’s  

WAC. 

Connect sensor to GE Lighting Solutions L L C LED drivers or control modules not capable of providing greater than 

15VA power, including but not Limited to models GED50MCC2P1000, GED36MCC2P700 and GED100MCC2P480

2

1