Symbol Technologies DM4046 Manual De Usuario
Hearing Aid Compatibility
This product is marked HAC showing compliance with the
applicable requirements of FCC Part 68 and CS03-Part 5.
applicable requirements of FCC Part 68 and CS03-Part 5.
Radio Frequency Interference
Requirements for Home or Office Use
Requirements for Home or Office Use
This device has been tested and found to comply with the limits
for a Class B digital device pursuant to Part 15 of the Federal
Communications Commissions (FCC) Rules and Regulation.
These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in
a residential environment. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause
harmful interference to radio communications.
for a Class B digital device pursuant to Part 15 of the Federal
Communications Commissions (FCC) Rules and Regulation.
These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in
a residential environment. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If the equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
in a particular installation. If the equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a circuit different
from that which the receiver is connected.
Radio Frequency Interference
Requirements-Canada
Requirements-Canada
This Class B digital apparatus meets the requirements of the
Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la Classe B respecte toutes les
exigences du Reglement sur le Materiél Brouilleur du Canada.
Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la Classe B respecte toutes les
exigences du Reglement sur le Materiél Brouilleur du Canada.
FCC RF Exposure Guidelines
To comply with RF safety requirements use the specific
belt clip. All other belt clips should be avoided and
may not comply with RF safety requirements. The
belt clip. All other belt clips should be avoided and
may not comply with RF safety requirements. The
FCC has granted an Equipment Authorization for
NetVision phones with all reported Specific Absorption Rate
(SAR) levels evaluated as in compliance with the FCC RF
emission guidelines. SAR information on NetVision phones is on
file with the FCC and can be found under the Display Grant
section of http://www.fcc.gove/oet/fccid.
(SAR) levels evaluated as in compliance with the FCC RF
emission guidelines. SAR information on NetVision phones is on
file with the FCC and can be found under the Display Grant
section of http://www.fcc.gove/oet/fccid.
European Economic Area
The European variant is intended for use throughout the
European Economic area, however authorization for use
restricted as follows:
European Economic area, however authorization for use
restricted as follows:
• European standards dictate maximum radiated transmit
power of 100 mW, EIRP and frequency range 2.400 -
2.4835 GHz
2.4835 GHz
• France, the equipment is to be restricted to the 2.4465 -
2.4835 GHz frequency range
• Belgium outside, the equipment is to be restricted to the
2.460 - 2.4835 GHz frequency range
• Operation in Italy requires a user license.
Hereby, Symbol Technologies, Inc., declares that this
product is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC.
A Declaration of Conformity may be obtained from
http://www2.symbol.com/doc/.
product is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC.
A Declaration of Conformity may be obtained from
http://www2.symbol.com/doc/.
Laser Devices
(Only applies to Data Phone-4046)
(Only applies to Data Phone-4046)
Symbol products using lasers comply with US 21 CFR1040.10,
Subchapter J and IEC825/EN 60 825 (or IEC825-1/EN
60-825-1, depending on the date of manufacture). The laser
classification is marked on one of the labels on the product.
Subchapter J and IEC825/EN 60 825 (or IEC825-1/EN
60-825-1, depending on the date of manufacture). The laser
classification is marked on one of the labels on the product.
Class 1 Laser devices are not considered to be hazardous when
used for their intended purpose. The following statement is
required to comply with US and international regulations:
used for their intended purpose. The following statement is
required to comply with US and international regulations:
Use of controls, adjustments or performance
of procedures other than those specified herein
of procedures other than those specified herein
may result in hazardous visible or invisible laser
light exposure.
light exposure.
Class 2 laser scanners use a low power, visible light diode.
As with any very bright light source, such as the sun, the user
should avoid staring directly into the light beam. Momentary
exposure to a Class 2 laser is not known to be harmful.
As with any very bright light source, such as the sun, the user
should avoid staring directly into the light beam. Momentary
exposure to a Class 2 laser is not known to be harmful.
Samples of Laser Warning Labels
CAUTION: LASER LIGHT WHEN OPEN. DO NOT STARE INTO BEAM.
ATTENTION - LUMIERE LASER EN CAS D'OUVERTURE NE PAS REGARDER DANS LE FAISCEAU.
VORSICHT - LASERLICHT, WENN ABDECKUNG GOFFNET. NICHT IN DEN STRAHL BLICKEN.
ATTENTION - LUMIERE LASER EN CAS D'OUVERTURE NE PAS REGARDER DANS LE FAISCEAU.
VORSICHT - LASERLICHT, WENN ABDECKUNG GOFFNET. NICHT IN DEN STRAHL BLICKEN.
LASER LIGHT - DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
LASERLICHT-NICHT IN DEN STRAHL BLICKEN
LASER KLASSE 2
LUMIERE LASER - NE PAS REGARDER DANS LE FAISCEAU
APPARIEL A LASER CLASS 2
630 - 680 nm. 1mw
LASER LIGHT DO NOT STARE INTO BEAM
630 - 680nm LASER 1.0mW MAX OUTPUT
CLASS II LASER PRODUCT
CLASS II LASER PRODUCT