Gigaset A220A Duo A220A DUO Manual De Usuario
Los códigos de productos
A220A DUO
Lombok / Großbritannien - Irland / A31008-M2401-L101-1-7619 / Lombok.fm / 27.02.2012
V
e
rsi
on 4
, 16.09
.2005
4
Initial charging and discharging of the batteries
The correct charge status can only be displayed if the batteries are first fully charged
and discharged.
and discharged.
Please note
◆
The handset is pre-registered with the base. If you have purchased a
model with multiple handsets, all handsets will already be registered
with the base. You do not need to register the handset again. The internal
handset number appears in the top left of the display, e.g. 1 (
model with multiple handsets, all handsets will already be registered
with the base. You do not need to register the handset again. The internal
handset number appears in the top left of the display, e.g. 1 (
¢
page 1).
However, if a handset is not registered with the base (Register HS or Put
into base is displayed), please register the handset manually (
into base is displayed), please register the handset manually (
¢
page 9).
◆
If you have purchased multiple devices, you can upgrade your Gigaset to
a cordless PABX by registering all A120/A220 handsets at the same base
(
a cordless PABX by registering all A120/A220 handsets at the same base
(
¢
page 9).
◆
After the first battery charge and discharge, you may place your handset
in the charger after every call.
in the charger after every call.
◆
Always repeat the charging and discharging procedure if you remove the
batteries from the handset and reinsert them.
batteries from the handset and reinsert them.
◆
The batteries may warm up during charging. This is not dangerous.
◆
After a while, the charge capacity of the batteries will decrease for techni-
cal reasons.
cal reasons.
6.5
h
¤
Charge the handset in the base for 6.5 hours.
¤
After charging, remove the handset from the
base and only replace it when the batteries are
fully discharged.
base and only replace it when the batteries are
fully discharged.
Please note
The handset must only be placed in the desig-
nated Gigaset base or charging cradle.
nated Gigaset base or charging cradle.
Setting the date and time
Set the date and time so that the correct date and time can be assigned to incoming
calls, and so that the alarm can be used.
calls, and so that the alarm can be used.
MENU
¤
u
Settings
¤
OK
¤
Date/Time
¤
OK
¤
Date
¤
~
(enter the day, month
and year in 6-digit format)
¤
OK
¤
Time
¤
~
(enter hours and minutes in 4-digit
format)
¤
OK (display message: Saved)
¤
a
(press and hold to return to idle status)
When entering the time and date, you can move the position of an entry to the left or
right by pressing the control key
right by pressing the control key
u
up or down.
Please note
If your phone receives the date and time during calling line display (e.g., via your
network provider, a router or PABXs), you can specify whether this data should be
copied to your phone:
network provider, a router or PABXs), you can specify whether this data should be
copied to your phone:
¤
Press the key sequence: MENU
¤
P#Q5#MI
The following is displayed;
the current setting flashes:
¤
Press one of the following keys to specify, when this data should be copied to
your phone:
your phone:
Q
Never
or
1
Once, in case the date/time is not set on your phone
or
2
Always
Your selection is displayed (e.g. 2):
¤
Press the display key OK.
973 SET: [0]
973 SET: [2]
© Gigaset Communications GmbH 2012
All rights reserved. Subject to availability.
Rights of modification reserved.
www.gigaset.com
This user guide is made from 100 % recycled paper.
Issued by
Gigaset Communications GmbH
Frankenstr. 2a
46395 Bocholt
Germany