BI Automotive SOLAR-BATTERIESCHUTZ IM KOFFER 35 W TPS- 936N-M Hoja De Datos

The product is intended for the conversion of sunlight into electrical power. Due to the practical 
design, the product is easy to transport. An integrated adjustable foot enables an optimum 
alignment towards the sun.
To operate consumer loads via the product, a suitable solar charge controller and an appropri-
ate buffer battery are required. 
Using a sliding switch the product can be operated and used on solar charge controllers with 
a voltage of 12 V or 24 V. 
Always observe the safety instructions and all other information included in these operating 
instructions.
This product complies with the applicable national and European requirements. All names of 
companies and products are the trademarks of the respective owners. All rights reserved.

• Solar case
• Cable set
• Operating instructions 

   The warranty will be void in the event of damage caused by non-compliance 

 

•  The unauthorised conversion and/or modifi cation of the product is not allowed 

because of safety reasons. 

 

•  The product is not a toy; keep it away from children.

 

•   Do not leave the packaging material carelessly lying around, since it could become 

a dangerous plaything for children.

 

•  The covers of the solar case contain magnets which are used to lock the product.  

Therefore, keep e.g. clocks, magnetic data carriers (for example, bank card with 
magnetic strip) away from the product.

 

•  Handle the product with care; it can be damaged by impacts, blows, or accidental 

falls, even from a low height. 

 

•  Choose an appropriate mounting place. It has to be stable, level and suffi ciently 

large.

 

   Furthermore, you have to make sure there is direct solar irradiation at the mount-

ing location to ensure an optimum power output.

 

•  Install the product in such a way that it cannot be tripped over. The same applies 

to the positioning of the connection cables.

 

   Make sure the cables cannot be damaged by sharp edges.

 

• The product must not get damp or wet.

 

•  Do not place the product on sensitive surfaces without using suffi cient protection, 

as this can cause scratches or pressure marks.

 

•   To operate the product, a suitable charge controller, and where applicable, a buffer 

accumulator are required.

 

•  Using the sliding switch, always select the suitable nominal voltage (12 V or 24 V) 

for the charge controller used.

 

•   If you have any questions that are not answered in this manual, please contact our 

technical service or another specialist.

•   Open the solar case. The two halves are held together only by a magnetic lock. 
•   On the rear of the solar case there are two fold-out and height-adjustable feet. Align the solar 

cells towards the sun. Depending on the position of the sun, adjust the inclination using the 
feet.

•  Select the corresponding nominal voltage with the sliding switch (at the bottom, near the 

cable compartment) for the charge controller used.

•  Unwind the connection cable completely.
   To operate consumer loads, a suitable charge controller is required (at the time of creation 

of this operating manual, the best suitable product was e.g. item no. 856345 (for 12 V), not 
included in the delivery, must be ordered separately) and where applicable, a buffer accumu-
lator (e.g. a suitable solar lead accumulator).

   The connection cables enclosed can be connected to the output of the charge controller and 

are used to connect a load.

•   The blue LED next to the sliding switch fl ashes to indicate and control the functioning when 

suffi cient sunlight shines onto the solar module.

•   Align the product several times per day so that you are able to use the sunlight for power 

production in an optimum way.

•   If you don’t use the product any longer, clean it thoroughly before you wind up the cable (ca-

ble compartment at the bottom in the solar case) and then close it. Select a storage location 
that is dry, clean and free of dust.

Maintenance or repair may be performed only by qualifi ed personnel or a specialised repair 
shop. The product contains no parts that require servicing. Therefore, do not dismantle it.
Use a clean, dry, soft cloth for cleaning. Do not press too strongly onto the casing or the inte-
grated solar module as this will lead to scratch marks or damage to the product.

 Do not use abrasive cleaning agents, cleaning alcohol or other chemical solutions, 
since these could damage the housing or even impair operation. 

    Dispose of the product at the end of its serviceable life in accordance with the 

current statutory requirements; e. g. return it to any suitable collection point.

 

Item No. 401985 

Item No. 404873

Output .......................................13 W 

35 W

Nominal voltage  ....................... switchable 12/24 V 

switchable 12/24 V

Solar cell type ...........................amorphous  

mono crystalline

Cable length .............................3 m 

3m

Fuse in vehicle adaptor ............F2A/250 V, 5 x 20 mm 

F3A/250 V, 5 x 20 mm 

Dimensions ...............................525 x 390 x 37 mm 

525 x 390 x 37 mm

Weight ......................................4.75 kg 

5.1 kg

 

  

   These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,  

D-92240 Hirschau (www.conrad.com). 

 

 All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfi lming, 
or the capture in electronic data processing systems require the prior written approval by the editor. 
Reprinting, also in part, is prohibited. 

 

 These operating instructions represent the technical status at the time of printing. Changes in         
technology and equipment reserved.