Eurotronic Thermostat head 8 up to 28 °C Eurotronic 700 100 331 Manual De Usuario

Los códigos de productos

700 100 331

Installation

SPARmatic Zero can be quickly and easily mount-
ed on all common valves (see adapter table). It
can be installed without grime and water spots
because the heating circuit is not interrupted.

1. Turn the manual thermostat head up complete-

ly, loosen the fastening and pull the thermostat
off of the valve.

2. Use an appropriate adapter, if required,

and push it onto the valve.

3. Screw the connector on the valve or the

adapter.

4. Now, you put SPARmatic Zero on the

connector until it noticeably clicks into place.

ATTENTION: It must be possible to insert SPAR-

matic Zero without applying force, ensure that the
appliance is in the „

“ or „

“ position.

valve – adapter – coupling ring

valve – coupling ring

Additional information about the different adapters
are provided on page 20 or at:

www.eurotronic.org

Setting heating and economy

times

With SPARmatic Zero it is possible to set 4 heating

and 4 economy times per day – one for each day

or one for a block of several days.

TAG1 to TAG7 represent the weekdays from Mon-

day to Sunday. Additionally, the corresponding

days are shown as abbreviation below the menu

bar on the display.
Block construction:
T1– 5 = same programme from Monday to Friday

1– 6 = same programme from Monday to Satur-

day
T 1– 7 = same programme from Monday to Sunday

For non-programmed days the factory preset
remains active.

Setting of an individual programme:
Press

. Select the menu item

with the

Button or . Press

for Monday is

shown on the display. Select day/block with the
Button or . Confi rm with

. Set the begin-

ning of the 1

heating time (symbol )with the But-

ton or . Confi rm with

. Set the beginning

of the 1

economy time (symbol ) with the Button

or . Confi rm with

➔

In case of a

later installation, please switch

in the menu to

before you install the

device. Herewith the installation is facilitated.
Only mount it in this position.

Dismounting

➔

To remove SPARmatic Zero remove this at the

, position, wait for a short period and then

press on the unlocking device to detach the

quick-release catch. Then pull the SPARmatic
Zero from the valve.

ess

Now, if desired, a 2

, 3

or 4

heating/economy

time can be entered.
➔

If you do not want to set a further heating/
economy time confi rm „

“ with

The next day for programming is shown on the

display.
➔

If you do not want to enter a further day, leave
the menu with

. If the temperature is

shown on the display the programming is

fi nished.

➔

Within the blocks you can also overwrite single
days with differing times.

Setting comfort and economy

temperature

Press

. Select the menu item

with the

Button or . Confi rm with

. Set comfort

temperature with the Button or . Confi rm
with

. Set the economy temperature with the

Button or . Confi rm with

Area

: 8°C, freeze protection function is active

Area

: valve is completely open

Adaptation

Initial installation: Press the button

until

appears on the display so that SPARmatic

Zero will be able to start its adaptation. The
device will adapt itself to the stroke of your valve
body. To do this the valve will now be opened and
closed several times to store the end points.
In some cases this process can take a few
minutes. After successful adaptation it returns to
normal mode.

➔

Should adaptation become necessary again,
e.g. if your radiator does not cool down in the

-Position, please press in the menu the

button

until adaptation starts again.

➔

If the mistake is shown on the display place
SPARmatic Zero onto the radiator valve and
then take the batteries out for a short time in
order to execute a reset.

➔

By the way: Maximum energy saving can be

obtained with an economy temperature which

is about 5 ˚C below the comfort temperature.

Manual operation

With the Button or an adaptation of the

room temperature is possible at any time. In

the AUTO-mode it remains active until the next

switch point is reached. Now, the usual pro-

gramme becomes active again.

Further functions

Timer function
The timer function is selected with the timer-
button

. With this function an user-defi ned

temperature for a programmable period can
be entered. This can be very useful in case of a
party, for example. Press

. First, the time for

which the time programme has been deactivated
is shown. Confi rm with

. Now, the desired

temperature can be set. Confi rm with

Basic operating modes

MANU-mode
In the MANU-mode SPARmatic Zero adjusts to
the manually specifi ed temperature.
AUTO-mode
In the AUTO-mode SPARmatic Zero changes
between to temperatures according to the time
programme that has been set:

comfort temperature (factory preset 21°C)

economy temperature (factory preset 16°C)
The heating and economy times can be specifi ed
via the adjustable time programme. It is possible
to set 8 switch points (4 heating and 4 economy
times) per day at the most. SPARmatic Zero has
the following factory preset:
Heating time:
Heating with comfort temperature
(factory preset: 1

heating time at 07:00)

Economy time:
lowering to economy temperature
(factory preset: 1

economy time at 22:00)

Offset
If the perceived temperature signifi cantly differs
from the set thermostat temperature a tempera-
ture set up can be executed.
Press

. Select the menu item

with the

Button or . Confi rm with

. The degree

setting

will fl ash on the display. Now, set

up the desired adaptation for the temperature
(from -5 up to +5°C) with the Button or .
Confi rm your entry with

. The temperature

display does not change!
Window function
If you open a window and consequently the
temperature drops signifi cantly, SPARmatic
Zero will automatically close the heating valve
in order to save energy. The display will show

. Afterwards, SPARmatic Zero will resume

normal operation. For the set up select

the menu. Confi rm with

. First, the sensibil-

ity is selected with the Button or (

high sensibility,

= medium sensibility (factory

preset),

= low sensibility). Confi rm with

Now, you enter the time (10 min (factory preset) -
60 min) for which the valve should remain closed.
Confi rm with