Blade 180 QX HD RTF BLH7400 Hoja De Datos

The Battery Charger (EFLC1010) included with your 
quadcopter has been designed to safely charge the Li-Po 
battery.

CAUTION: All instructions and warnings must be 
followed exactly. Mishandling of Li-Po batteries can 

result in a fi re, personal injury and/or property damage.

• By handling, charging or using the included Li-Po battery, 

you assume all risks associated with lithium batteries.

• If at any time the battery begins to balloon or swell, 

discontinue use immediately. If charging or discharging, 
discontinue and disconnect. Continuing to use, charge or 
discharge a battery that is ballooning or swelling can result 
in fi re.

• Always store the battery at room temperature in a dry area 

for best results.

• Always transport or temporarily store the battery in a tem-

perature range of 40–120º F (5–49° C). Do not store battery 
or model in a car or direct sunlight. If stored in a hot car, the 
battery can be damaged or even catch fi re.

• Always charge batteries away from fl ammable materials.
• Always inspect the battery before charging.
• Always disconnect the battery after charging, and let the 

charger cool between charges.

• Always constantly monitor the temperature of the battery 

pack while charging.

• ONLY USE A CHARGER SPECIFICALLY DESIGNED TO CHARGE 

LI-PO BATTERIES. Failure to charge the battery with a 
compatible charger may cause a fi re resulting in personal 
injury and/or property damage.

• Never discharge Li-Po cells to below 3V under load.
• Never cover warning labels with hook and loop strips.
• Never leave charging batteries unattended.
• Never charge batteries outside recommended levels.
• Never charge damaged batteries.
• Never attempt to dismantle or alter the charger.
• Never allow minors to charge battery packs.
• Never charge batteries in extremely hot or cold places 

(recommended between 40–120° F or 5–49° C) or place in 
direct sunlight.

NOTICE: Charge only batteries that are cool to the touch 
and are not damaged. Look at the battery to make sure it 
is not damaged e.g., swollen, bent, broken or punctured. 

1. Insert the charger into a USB port.
2. Properly connect the battery to the charger lead. 
3. Always disconnect the fl ight battery from the charger 

immediately upon completion of charging.

CAUTION: Only use chargers specifi cally 
designed to charge the included Li-Po battery. 

Failure to do so could result in fi re, causing injury or 
property damage.

CAUTION: Never exceed the recommended 
charge rate.

LED Indications
When you make the connection successfully, the LED on the charger turns solid red, indicating charging has begun.
Charging a fully discharged (not over-discharged) 500mAh battery takes approximately 60 minutes. The light goes out
when the charge is complete.

CHARGING (Solid Red)
MAX CHARGE (OFF)

CAUTION: Once charging is complete, immediately remove the battery. Never leave a battery connected to the 
charger.

SOLID RED LED

–Charging

DC Input:5.0V    500mA

DC Output:4.2V    500mA

LED OFF

–Charge 

Complete

•  Remove and inspect contents
•  Begin charging the fl ight battery
•   Install the fl ight battery in the quadcopter 

(once it has been fully charged)

•  Program your computer transmitter (BNF only)
•  Bind your transmitter (BNF only)
•  Familiarize yourself with the controls
•  Find a suitable area for fl ying

❏ Always turn the transmitter on fi rst

 

❏  Plug the fl ight battery into the lead from the 5-in-1 

control unit

 

❏  Allow the 5-in-1 control unit to initialize and arm 

properly

 

❏ Fly the model

 

❏ Land the model

 

❏  Unplug the fl ight battery from the 5-in-1 control unit

❏ Always turn the transmitter off last