AEG PW 5570 FA 520570 Hoja De Datos

Use the SET, UNIT,   (UP) and   (DOWN) buttons to 
change the stored settings.

The scales are factory set with the units “kg“ and “cm“.

To change the settings to “lb“ or “st“ as well as “Ft:in“, 
proceed as follows:
•  Switch the scales on by applying gentle pressure to the 

surface with your foot or toe.

•  Press the UNIT button until the desired unit of weight 

is displayed. The unit for the height also automatically 
changes.

Weighing Function
•  Place the scale on a hard, flat surface (avoid carpets). An 

uneven floor contributes to inaccurate measurements.

•  Stand on the scales with both feet. The device switches 

on automatically.

•  Distribute your weight equally and wait for the scale to 

determine your weight.

•  The digits on the display will flash before your exact 

weight will be shown.

•  In order to extend the battery life, the device will auto-

matically turn off 10 seconds after you have stepped off 
the scale.

•  The scale has default values that you can change, as 

described below.

•  Carry out the following steps in sequence and within a 

few seconds. Otherwise, the device will automatically 
cancel input mode.

•  Press the button SET. The memory space will flash on the 

display (USER). Confirm the setting by pressing SET or se-
lect another memory space by pressing the UP / DOWN 
button. Then press SET to go to the next setting.

•  The symbol for “male” or “female” will flash. Confirm the 

setting by pressing SET or use the UP / DOWN button to 
choose the symbol for your gender. Then press SET to go 
to the next setting.

•  The height setting will flash. Select your height by press-

ing UP or DOWN button. Holding down one of the 
buttons will accelerate the process. Confirm your entry by 
pressing SET.

•  The setting AGE will flash. Select your age by pressing UP 

or DOWN button. Holding down one of the buttons will 
ac-celerate the process. Confirm your entry by pressing 
SET.

•  The default symbol for the “unathletic“ type flashes. 

Which type do you consider yourself to be? Select your 

type using the UP or DOWN button: “unathletic“, “aver-
age“ or “athletic“. Confirm your selection with SET.

•  If only the stored position and the display 0.0 kg  

(0.0 lb/0:0 st) is still shown, input mode for this stored 
position is completed.

You now have the following options:
•  You can change the units for weight and type. Press the 

UNIT button until the desired unit of weight is displayed. 
The unit for the height automatically changes.

•  Press the SET button to see the selected settings again.
•  Allocate further memory spaces. There are 10 spaces 

avail-able in total. Press SET and change the space by 
pressing the UP or DOWN button. Proceed further as 
described above.

•  If you want to make changes, press SET (USER flashes). 

Select the stored position using the UP or DOWN but-
ton. Proceed further as described above.

•  You can immediately start measuring.

Measurement and Analysis
Record your personal data in the memory.

•  The device can only function correctly if you stand on 

the device with bare, dry feet!

•  If necessary wipe the contact surfaces to improve 

results.

•  Due to the significant fluctuation of body fat, it is 

difficult to attain a standard value. On average the 
optimal testing time is between 6 p.m. and 8 p.m, since 
the body fat remains very consistent during this period 
of time.

•  Press the SET button. The preset stored position data ap-

pears on the display (USER flashes). Use the UP / DOWN 
button to select the stored position at which your data is 
saved.

•  Wait for the USER display and 0. 0 kg (0.0 lb/st) to stop 

flashing.

•  Stand on the contact surfaces (4) of the scales with both 

feet.

•  Firstly your weight will flash on the display.
•  After a few seconds, the following results will be shown:

1.  - the body fat content in % (   symbol) 

- the body water content in % (   symbol)
- the results analysis in the form of a bar 

2.  - the muscle mass content in % (   symbol) 

- the bone mass content in % (   symbol) 
- the calorie requirement per day

3.  - The preset gender 

- The preset type 
- The preset height 
- The preset age (AGE)
- The weight gain (INCREASE) / the weight loss  

(DNCREASE) in kg (lb/st) in comparison to the previ-
ous measurement