Kingston Technology 3GB, 1066MHz, DDR3, ECC, CL7, DIMM (Kit of 3) KVR1066D3E7K3/3G Hoja De Datos
Los códigos de productos
KVR1066D3E7K3/3G
Memory Module Specifications
KVR1066D3E7K3/3G
3GB (1GB 128M x 72-Bit x 3 pcs.) PC3-8500
CL7 ECC 240-Pin DIMM Kit
CL7 ECC 240-Pin DIMM Kit
Kingston.com
Document No. VALUERAM0858-001.A00 09/18/09 Page 1
DESCRIPTION
ValueRAM’s KVR1066D3E7K3/3G is a kit of three 128M x
72-bit 1GB (1024MB) DDR3-1066 CL7 SDRAM (Synchronous
DRAM) ECC memory modules, based on nine 128M x 8-bit
DDR3-1066 FBGA components per module. Total kit capac-
ity is 3GB. The SPDs are programmed to JEDEC standard
latency 1066Mhz timing of 7-7-7 at 1.5V. Each 240-pin DIMM
uses gold contact fingers and requires +1.5V. The electrical
and mechanical specifications are as follows:
72-bit 1GB (1024MB) DDR3-1066 CL7 SDRAM (Synchronous
DRAM) ECC memory modules, based on nine 128M x 8-bit
DDR3-1066 FBGA components per module. Total kit capac-
ity is 3GB. The SPDs are programmed to JEDEC standard
latency 1066Mhz timing of 7-7-7 at 1.5V. Each 240-pin DIMM
uses gold contact fingers and requires +1.5V. The electrical
and mechanical specifications are as follows:
FEATURES
• JEDEC standard 1.5V ± 0.075V Power Supply
• VDDQ = 1.5V ± 0.075V
• 533MHz fCK for 1066Mb/sec/pin
• 8 independent internal bank
• Programmable CAS Latency: 5,6,7,8,9,10
• Posted CAS
• Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
• Programmable CAS Write Latency(CWL) = 6(DDR3-1066)
• 8-bit pre-fetch
• Burst Length: 8 (Interleave without any limit, sequential with
• VDDQ = 1.5V ± 0.075V
• 533MHz fCK for 1066Mb/sec/pin
• 8 independent internal bank
• Programmable CAS Latency: 5,6,7,8,9,10
• Posted CAS
• Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
• Programmable CAS Write Latency(CWL) = 6(DDR3-1066)
• 8-bit pre-fetch
• Burst Length: 8 (Interleave without any limit, sequential with
starting address “000” only), 4 with tCCD = 4 which does
not allow seamless read or write [either on the fly using A12
or MRS]
not allow seamless read or write [either on the fly using A12
or MRS]
• Bi-directional Differential Data Strobe
• Internal(self) calibration : Internal self calibration through ZQ
• Internal(self) calibration : Internal self calibration through ZQ
pin (RZQ : 240 ohm ± 1%)
• On Die Termination using ODT pin
• Average Refresh Period 7.8us at lower than TCASE 85°C,
• Average Refresh Period 7.8us at lower than TCASE 85°C,
3.9us at 85°C < TCASE ≤ 95°C
• Asynchronous Reset
• 1066Mbps CL7 doesn’t have backward compatibility with
• 1066Mbps CL7 doesn’t have backward compatibility with
800Mbps CL5
• PCB : Height 1.180” (30.00mm), single sided component
SPECIFICATIONS
CL(IDD)
7 cycles
Row Cycle Time (tRCmin)
50.63ns (min.)
Refresh to Active/Refresh
110ns
Command Time (tRFCmin)
Row Active Time (tRASmin)
37.5ns (min.)
Power
1.147 W (operating per module)
UL Rating
94 V - 0
Operating Temperature
0° C to 85° C
Storage Temperature
-55° C to +100° C
Continued >>