Black & Decker RO410 Manual De Usuario

linseed oil, etc.) can self-ignite in sander dust bag or elsewhere and cause fire. To
reduce risk, empty bag frequently and strictly follow sander manual and coating
manufacturer's instructions. 
Your sander comes equipped with a cloth dustbag to collect the dust generated while
sanding. To attach the dustbag onto the sander simply slide it firmly into the dust extraction
port at the back of the sander. 
To empty the dust dustbag, remove it from the sander by pulling it straight back. Dump the
sanding debris into an appropriate trash receptacle. 
You may, if you prefer, attach a vacuum cleaner to the tool to collect the dust as you sand. 
A vacuum hose adaptor is available as a service part at extra cost. To find your nearest
Black & Decker Service Center location, refer to the yellow pages directory under "Tools—
Electric" or call: 1-800-544-6986. 
To use the adaptor, remove the dust bag and replace it with the adaptor, then install a
vacuum hose. 
Ensure that the vacuum cleaner can be placed such that it will not tip over or interfere with
the motion of the sander. If this cannot be done, do not use the vacuum cleaner. Turn on the
vacuum cleaner before beginning to sand and turn it off after turning off the sander. Empty
vacuum cleaner as required. 

Use only mild soap and damp cloth to clean the tool. Many household cleaners contain
chemicals which could seriously damage the plastic and gel components. Also do not use
gasoline, turpentine, lacquer or paint thinners or similar products. Never let any liquid get
inside the tool; never immerse any part of the tool into a liquid. 
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment should be performed by authorized service centers or other qualified service
personnel, always using identical replacement parts.

• Unit will not start.

• Cord not plugged in.

• Plug tool into a working 
outlet.

• Circuit fuse is blown.

• Replace circuit fuse. 
(If the product repeatedly 
causes the circuit fuse to 
blow, discontinue use 
immediately and have it 
serviced at a Black &
Decker service center or 
authorized servicer.)

• Circuit breaker is tripped.

• Reset circuit breaker. 
(If the product repeatedly 
causes the circuit breaker 
to trip, discontinue use 
immediately and have it 
serviced at a Black &
Decker service center or 
authorized servicer.)

• Cord or switch is damaged.

• Have cord or switch 
replaced at Black & 
Decker Service Center or 
Authorized Servicer.

For assistance with your product, visit our website www.blackanddecker.com for the 
location of the service center nearest you or call the BLACK & DECKER help line at
1-800-544-6986.

Recommended accessories for use with your tool are available from your local dealer or
authorized service center. If you need assistance regarding accessories, please call: 
1-800-544-6986.

The use of any accessory not recommended for use with this tool could be

hazardous.

Black & Decker offers a full network of company-owned and authorized service locations
throughout North America. All Black & Decker Service Centers are staffed with trained
personnel to provide customers with efficient and reliable power tool service.
Whether you need technical advice, repair, or genuine factory replacement parts, contact the
Black & Decker location nearest you. To find your local service location, refer to the yellow
pages directory under "Tools—Electric" or call: 1-800-544-6986.

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material
or workmanship. The defective product will be replaced or repaired at no charge in either of
two ways.
The first, which will result in exchanges only, is to return the product to the retailer from
whom it was purchased (provided that the store is a participating retailer). Returns should be
made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after
the sale). Proof of purchase may be required. Please check with the retailer for their specific
return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or
authorized Service Center for repair or replacement at our option. Proof of purchase may be
required. Black & Decker owned and authorized Service Centers are listed under "Tools-
Electric" in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights
and you may have other rights which vary from state to state. Should you have any
questions, contact the manager of your nearest Black & Decker Service Center. This product
is not intended for commercial use.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-544-6986 for a free replacement.

SYMBOLS
The label on your tool may include the following symbols.

V ..........................volts

A..........................amperes

Hz ........................hertz

W ........................watts

min ........................minutes

......................alternating current

......................direct current

no ........................no load speed

..........................Class II Construction

........................earthing terminal

........................safety alert symbol

.../min ..................revolutions or 

reciprocations
per minute

• ALWAYS WEAR EYE AND RESPIRATORY PROTECTION.
• Clean your tool out periodically.

When using an extension cord, be sure to use one heavy enough to carry the current your
product will draw. An undersized cord will cause a drop in line voltage resulting in loss of
power and overheating. The following table shows the correct size to use depending on cord
length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the
gage number, the heavier the cord.

Sanding of lead based paint is NOT RECOMMENDED due to the difficulty of controlling the
contaminated dust. The greatest danger of lead poisoning is to children and pregnant
women.
Since it is difficult to identify whether or not a paint contains lead without a chemical analysis,
we recommend the following precautions when sanding any paint: 

• No children or pregnant women should enter the work area where the paint sanding is

being done until all clean up is completed.

• A dust mask or respirator should be worn by all persons entering the work area. The filter

should be replaced daily or whenever the wearer has difficulty breathing.
NOTE: Only those dust masks suitable for working with lead paint dust and fumes should
be used. Ordinary painting masks do not offer this protection. See your local hardware
dealer for the proper (NIOSH approved) mask.

• NO EATING, DRINKING or SMOKING should be done in the work area to prevent

ingesting contaminated paint particles. Workers should wash and clean up BEFORE
eating, drinking or smoking. Articles of food, drink, or smoking should not be left in the work
area where dust would settle on them.

• Paint should be removed in such a manner as to minimize the amount of dust generated.
• Areas where paint removal is occurring should be sealed with plastic sheeting of 4 mils

thickness.

• Sanding should be done in a manner to reduce tracking of paint dust outside the work

area.

• All surfaces in the work area should be vacuumed and thoroughly cleaned daily for the

duration of the sanding project. Vacuum filter bags should be changed frequently.

• Plastic drop cloths should be gathered up and disposed of along with any dust chips or

other removal debris. They should be placed in sealed refuse receptacles and disposed of
through regular trash pick-up procedures. During clean up, children and pregnant women
should be kept away from the immediate work area.

• All toys, washable furniture and utensils used by children should be washed thoroughly

before being used again.

Be sure your power supply agrees with nameplate marking. 120 Volts AC only means your
tool will operate on standard 60 Hz household power. Do not operate AC tools on DC. A
rating of 120 volts AC/DC means that you tool will operate on standard 60 Hz AC or DC
power. This information is printed on the nameplate. Lower voltage will cause loss of power
and can result in over-heating. All Black & Decker tools are factory-tested; if this tool does
not operate, check the power supply.

Always unplug sander from power supply before any of the following

operations.

To reduce the risk of serious personal injury, read, understand and follow all

important safety warnings and instructions prior to using this tool.

To attach sandpaper, carefully center the cloth side of the paper over the sanding pad.  Press
the paper firmly in place. The hook and loop paper can be removed by simply pulling it off. 

To turn the tool ON, push the portion of the dust protected switch marked "I". To turn the tool
OFF, push the portion of the switch marked "O".

The design of the Random Orbit Sander allows for several different gripping methods. Three
basic methods are:
Figure 2 - One handed operation on the top of the sander.
Figure 3 - One handed operation holding the body of the sander.
Figure 4 - Two handed operation with one hand on the jug handle and the other on the body
or the top of the sander.

Grasp the sander and turn it ON. Move it in long, sweeping strokes along the surface, letting
it do the work. Utilize an even pressure across the sanding pad. Excessive pressure in the
corner area may cause damage. Pushing down on the tool while sanding actually slows the
removal rate and produces an inferior quality finish. Check your work often. Sander is
capable of removing material rapidly.

120V

0-25

26-50

51-100

101-150

(0-7,6m)

(7,6-15,2m)   (15,2-30,4m) (30,4-45,7m)

240V

0-50

51-100

101-200

201-300

(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m)

Ampere Rating
More

Not more

American Wire Gage

Than

Than

0

-

6

18

16

16

14

6

-

10

18

16

14

12

10

-

12

16

16

14

12

12

-

16

14

12

Not Recommended

Black & Decker (U.S.)

Inc., 

701 E. Joppa Rd.

Towson, MD 21286

U.S.A.