Whirlpool Duet W10254043C Manual De Usuario

Your installation may require additional parts. If you are interested 
in purchasing one of the items listed here, call the toll-free number 
on the cover or in the “Assistance or Service” section.

Laundry tub or 
standpipe taller 
than 96" (2.4 m)

Sump pump system (if not already 
available)

Overhead sewer

Standard 20 gal. (76 L), 30" (762 mm) tall 
drain tub or utility sink and sump pump 
(available from local plumbing suppliers)

Floor drain

Siphon break, Part Number 285834; 
additional drain hose Part Number 
8318155; and connector kit, Part 
Number 285835 

Drain hose too 
short

4 ft (1.2 m) drain hose extension kit, 
Part Number 285863

Water faucets 
beyond reach of fill 
hoses

2 longer water fill hoses: 6 ft (1.8 m) 

 

Part Number 76314, 10 ft (3.0 m) 

 

Part Number 350008 

You have the option of purchasing pedestals of different heights 
separately for this washer. You may select a 10" (254 mm) or a 
15.5" (394 mm) pedestal. These pedestals will add to the total 
height of the washer for a total height of approximately 
48" (1219 mm) or 53.5" (1359 mm).  

 

To order, call the dealer from whom you purchased your washer or 
refer to the “Assistance or Service” section. 

 

White

WHP1000SQ

Black

WHP1000SB

Diamond Dust (Silver)

WHP1000SU

White

XHP1550VW

Black

XHP1550VB

Diamond Dust (Silver)

XHP1550VU

New Aspen (Light Green)

XHP1550VA

Tuscan Chestnut

XHP1550VC

Ocean Blue

XHP1550VE

Cranberry Red

XHP1550WR

Lunar Silver

XHP1550WL

Are you planning to stack your washer and dryer? To do so you 
will need to purchase a Stack Kit.
To order, call the dealer from whom you purchased your dryer or 
refer to the “Assistance or Service” section. Ask for Part 
Number 8541503.

Selecting the proper location for your washer improves 
performance and minimizes noise and possible washer “walk.”
Your washer can be installed under a custom counter, or in a 
basement, laundry room, closet, or recessed area. See “Drain 
System.”
Companion appliance location requirements should also be 
considered. Proper installation is your responsibility.
You will need

■

A water heater set to deliver 120°F (49°C) water to the washer.

■

A grounded electrical outlet located within 6 ft (1.8 m) of 
where the power cord is attached to the back of the washer. 
See “Electrical Requirements.”

■

Hot and cold water faucets located within 4 ft (1.2 m) of the 
hot and cold water fill valves, and water pressure of 

 

20-100 psi (137.9-689.6 kPa).

■

A level floor with a maximum slope of 1" (25 mm) under entire 
washer. Installing the washer on soft floor surfaces, such as 
carpets or surfaces with foam backing, is not recommended.

■

A sturdy and solid floor to support the washer with a total 
weight (water and load) of 400 lbs (180 kg).

Do not operate your washer in temperatures below 32°F (0°C). 
Some water can remain in the washer and can cause damage in 
low temperatures.

■

The location must be large enough to allow the washer door to 
be fully opened.

■

Additional spacing should be considered for ease of 
installation and servicing.

■

Additional clearances might be required for wall, door, and 
floor moldings.

■

Additional spacing of 1" (25 mm) on all sides of the washer is 
recommended to reduce noise transfer.

■

Companion appliance spacing should also be considered.