Peripheral Electronics IPOD PGHSB1 Manual De Usuario

9

The quality controls used in the manufacture of this product will ensure your satisfac-

tion. This warranty applies only to the original purchaser of this product from an autho-

rized Peripheral Electronics dealer. This warranty covers any supplied or manufactured 

parts of this product that, upon inspection by

Peripheral Electronics authorized personnel, is found to have failed in normal use due 

to defects in material or workmanship. This warranty does not apply to installation ex-

penses. Attempting to service or modify this unit, operating this unit under conditions 

other than the recommended voltage will render this 

WARRANTY VOID.

Unless otherwise prescribed by law, Peripheral Electronics shall not be liable for any 

personal injury, property damage and or any incidental or consequential damages of 

any kind (including water damage) resulting from malfunctions, defects, misuse, im-

proper installation or alteration of this product. All parts of this Peripheral Electronics 

product are guaranteed for a period of 1 year as follows:

Within the first 12 months from date of purchase, subject to the conditions above,

Peripheral Electronics will repair or replace the product at their discretion, if it is de-

fective in material or workmanship providing it is returned to an Authorized Peripheral 

Electronic’s dealer, with PROOF OF PURCHASE from an authorized Peripheral Elec-

tronics dealer.

This equipment may be reset by unintentional electrostatic discharge during operation. 

Exposure to direct sunlight or extreme heat may cause damage or malfunction.

Interference Statement This equipment has been tested and found to comply with the 

limits for a Class B digital device, pursuant to Part 15 of FCC rules. These limits are 

designed to provide reasonable protection against harmful interference in a residential 

installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not 

installed and used in accordance with the instructions, may cause harmful interference 

to radio communications. However, there is no guarantee that interference will not oc-

cur in a particular installation. If this equipment does cause harmful interference to radio 

or television reception, which can be determined by turning the equipment off and on, 

the user is encouraged to try to correct the interference by one or more of the following 

measures:

1. Re-orientate or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that of which the 

    receiver is connected.

4. Consult the dealer or an experienced radio / television technical for help. Notice : 

    The changes or modifications not expressly approved by the party responsible for 

    compliance could void the user authority to operate the equipment.
For Best Performance Have It Professionally Installed.

www.peripheralelectronics.com

Peripheral Electronics®,

a division of AAMP of America™

13160 56th Court Clearwater, Florida 33760

Ph. 800-477-2267 ext. 230

support@peripheralelectronics.com

©2009 AAMP of Florida, Inc.

When I listen to 

the factory AM or 

FM radio there 

is only static, no 

audio.

Factory antenna 

cable is connected 

to the HD Radio 

tuner. 

Use Gateway to access HD Radio 

source. This will provide all AM and 

FM reception for your vehicle.

No AM or FM 

reception using the 

HD Radio source

Factory antenna 

cable is not 

connected to the HD 

Radio tuner (HDRT)

remove from factory radio, connect 

into HDRT module. Note* some 

vehicles need to use the supplied 

antenna adaptor to make this 

connection.

Radio shows iPod 

not connected

iPod cable is not 

connected to iPod or 

Gateway. 

Verify the docking cable is connected 

to the Media Gateway, and the iPod

I can not correctly 

control the iPod 

through the radio.

the iPod firmware 

may be out of date. 

Update iPod firmware for free at http://

www.apple.com/ipod/download

I have updated my 

iPod’s firmware 

and still have 

control issues

sometimes the 

iPods needs to be 

reset

Press and hold the click wheel (center 

button) and the menu button for 10 

seconds. This will reboot the iPod. 

YOU WILL NOT LOOSE MUSIC on 

the iPod by doing this reset

I don’t see iPod 

artist or song 

information on the 

screen

the radio is 

displaying a different 

text field

Press the Text / Scan button to see 

text

I can’t use my 

iPod’s click wheel 

to select music

the iPod is in 

external control 

mode. This allows 

text to be displayed 

on the radio screen

Press the Aux / Sat button and select 

AUX 2 source to control the iPod 

manually using the click wheel

the Media 

Gateway does 

not recognize the 

HD Radio tuner 

(HDRT)

the Gateway needs 

to be reset when 

connecting a new 

component such as 

the HDRT

disconnect the Gateway interface from 

the vehicle. Let it sit without power 

for 5 minutes. Use the 8-pin to 8-pin 

HDRT cable to connect the Tuner to 

the Media  Gateway, then connect to 

the vehicle