Perlick BBRN Manual De Usuario
Models BBR/BBS Installation & Operation Manual
Printed in USA
3
0213
PrIor To InsTallaTIon
Uncrating and Inspection
Remove all crating material. Carefully inspect
cabinet for hidden damage. If damage is
discovered, file your claim immediately with the
transport company. Perlick is not responsible for
damage in transit.
CAUTION
Do not cut cardboard
sleeve covering the unit.
Cutting may result in damage to the exterior
of the cabinet. Failure to follow this procedure
may damage the compressor and void
warranty.
1. Uncrate the unit on flat, level surface. Remove
1. Uncrate the unit on flat, level surface. Remove
the cardboard sleeve by removing the banding
securing the sleeve to the shipping base.
Carefully lift the cardboard sleeve up over the
top of the unit.
2. Carefully lift unit off the base and onto a hand
truck or dolly. Make sure unit is balanced
on transporting device using soft, flexible
strapping. Protect unit surfaces with cloth
material where strapping contacts unit.
CAUTION
Do not lift unit by drawer,
shelving or door handles
or damage to the unit could occur.
WARNING
To prevent personal
i n j u r y, t w o p e o p l e
minimum required to lift the unit. Larger units
may require additional personnel.
3. Before moving unit, secure door(s) to unit with
3. Before moving unit, secure door(s) to unit with
tape to prevent from opening.
4. Carefully move unit to installation site and
place in front of opening.
CAUTION
Finished flooring should
b e p r o t e c t e d w i t h
appropriate material to avoid damage from
moving the unit.
Plumbing
CAUTION
Do not over-tighten drain
fitting or damage to the
threads could occur.
Condensate from the cooling coil is automatically
Condensate from the cooling coil is automatically
evaporated from the condensate pan located in
the condensing unit housing on self-contained
models.
Each unit is equipped with a floor drain located
Each unit is equipped with a floor drain located
in the right rear corner of the cabinet. The drain
can be plumbed to an external floor drain by
connecting to the 3/4” NPT thread connection on
the side, or the 1” NPS thread connection out the
bottom, of the unit. Both drain ports come plugged
from the factory and can be removed if needed.
NOTE: Remote units require evaporator
NOTE: Remote units require evaporator
condensate to be plumbed to an external drain.
Electrical
The cabinet must be connected to a separately
fused power source (see Electrical Specification
Plate affixed to unit) in accordance with National
and Local electrical codes.
Self-contained Perlick units come equipped with
Self-contained Perlick units come equipped with
a NEMA 5-15P 90° plug with an 8’ cord extending
beyond the rear of the cabinet. The electrical
outlet must be flush with, or recessed into, the
wall surface.
NOTE: Never use an extension cord to extend the
NOTE: Never use an extension cord to extend the
power cord to the electrical receptacle.
CAUTION
If unit has been laid on its
back or sides, place unit
upright and allow minimum of 24 hours before
connecting power. Failure to follow this
procedure may damage the compressor and
void the warranty.
CAUTION
Do not attempt to operate
the equipment on any
other power source than that listed on the
Electrical Specification Plate attached to the
unit.
DANGER
ELECTROCUTION HAZARD!
Electrical grounding is
required. Appliances furnished with a 3-prong
(grounding) polarized plug are equipped for
your protection against possible shock
hazards.
• Never remove the round grounding prong
from the plug.
• Never use a 2-prong adapter.
• Never use extension cord to connect
power to the unit.
• If a 2-prong receptacle is encountered, or
a longer power cord is required, contact
a qualified electrician to have it replaced
in accordance with applicable electrical
codes.
DANGER
Failure to comply with these
electrical guidelines may
result in possible death or serious injury, fire,
or loss of property.