KitchenAid W10168334A Guía De Instalación

Before you move your refrigerator into its final location, it is 
important to make sure you have the proper electrical connection.

A 115 volt, 60 Hz., AC only 15- or 20-amp fused, grounded 
electrical supply is required. It is recommended that a separate 
circuit serving only your refrigerator be provided. Use an outlet 
that cannot be turned off by a switch. Do not use an 
extension cord.
IMPORTANT: If this product is connected to a GFCI (Ground Fault 
Circuit Interrupter) protected outlet, nuisance tripping of the 
power supply may occur, resulting in loss of cooling. Food quality 
and flavor may be affected. If nuisance tripping has occurred, and 
if the condition of the food appears poor, dispose of it. 
NOTE: Before performing any type of installation, cleaning, or 
removing a light bulb, turn the control (Thermostat, Refrigerator or 
Freezer Control depending on the model) to OFF and then 
disconnect the refrigerator from the electrical source. When you 
are finished, reconnect the refrigerator to the electrical source and 
reset the control (Thermostat, Refrigerator or Freezer Control 
depending on the model) to the desired setting.

Gather the required tools and parts before starting installation. 
Read and follow the instructions provided with any tools listed 
here.
TOOLS NEEDED:  

NOTE: Your refrigerator dealer has a kit available with a 

¹⁄₄" 

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing. 
Before purchasing, make sure a saddle-type valve complies with 
your local plumbing codes. Do not use a piercing-type or 

³⁄₁₆" 

(4.76 mm) saddle valve which reduces water flow and clogs more 
easily.
IMPORTANT:

■

All installations must meet local plumbing code requirements.

■

Use copper tubing and check for leaks. Install copper tubing 
only in areas where the household temperatures will remain 
above freezing.

A cold water supply with water pressure of between 30 and 
120 psi (207 and 827 kPa) is required to operate the water 
dispenser and ice maker. If you have questions about your water 
pressure, call a licensed, qualified plumber.

IMPORTANT: The pressure of the water supply coming out of a 
reverse osmosis system going to the water inlet valve of the 
refrigerator needs to be between 30 and 120 psi (207 and 
827 kPa).
If a reverse osmosis water filtration system is connected to your 
cold water supply, the water pressure to the reverse osmosis 
system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than 
40 to 60 psi (276 to 414 kPa):

■

Check to see whether the sediment filter in the reverse 
osmosis system is blocked. Replace the filter if necessary.

■

Allow the storage tank on the reverse osmosis system to refill 
after heavy usage.

■

If your refrigerator has a water filter, it may further reduce the 
water pressure when used in conjunction with a reverse 
osmosis system. Remove the water filter. See “Water Filtration 
System” in the Use & Care Guide.

If you have questions about your water pressure, call a licensed, 
qualified plumber.

Dispose of/recycle all packaging materials. Do not use sharp 
instruments, rubbing alcohol, flammable fluids, or abrasive 
cleaners to remove tape or glue. These products can damage the 
surface of your refrigerator.
IMPORTANT: 

■

Use 

³⁄₈" socket wrench to remove skids.

■

All four leveling legs must contact the floor to support and 
stabilize the full weight of the refrigerator.

■

Flat-blade screwdriver

■

⁷⁄₁₆" and ¹⁄₂" Open-end or two 

adjustable wrenches

■

¹⁄₄" Nut driver

■

¹⁄₄" Drill bit

■

Cordless drill

Your refrigerator is heavy. When moving the refrigerator for 
cleaning or service, be sure to cover the floor with 
cardboard or hardboard to avoid floor damage. Always pull 
the refrigerator straight out when moving it. Do not wiggle or 
“walk” the refrigerator when trying to move it, as floor 
damage could occur.