Brocade Communications Systems 12.4.00a Manual De Usuario
54
ServerIron ADX Security Guide
53-1002440-03
Configuring numbered and named ACLs
2
Specifying the maximum number of CAM entries for rule-based ACLs
For rule-based ACLs, you can adjust the allocation of Layer 4 CAM space for use by ACLs, on an IPC
or IGC basis and on 10 Gigabit Ethernet modules. The new allocation applies to all the ports
managed by the IPC or IGC or 10 Gigabit Ethernet module.
or IGC basis and on 10 Gigabit Ethernet modules. The new allocation applies to all the ports
managed by the IPC or IGC or 10 Gigabit Ethernet module.
Most ACLs require one CAM entry for each ACL entry (rule). The exception is an ACL entry that
matches on more than one TCP or UDP application port. In this case, the ACL entry requires a
separate Layer 4 CAM entry for each application port on which the ACL entry matches.
matches on more than one TCP or UDP application port. In this case, the ACL entry requires a
separate Layer 4 CAM entry for each application port on which the ACL entry matches.
Make sure you specify a maximum that is equal to or greater than the largest number of entries
required by an ACL applied to any of the ports managed by the same IPC or IGC. For example, if port
1 will have an ACL that requires 250 entries, make sure 250 is the lowest number of entries you
specify for any port on IPC 1 (the IPC that manages ports 1 – 24).
required by an ACL applied to any of the ports managed by the same IPC or IGC. For example, if port
1 will have an ACL that requires 250 entries, make sure 250 is the lowest number of entries you
specify for any port on IPC 1 (the IPC that manages ports 1 – 24).
To specify the maximum number of CAM entries the device can allocate for rule-based ACLs, enter
commands such as the following.
commands such as the following.
ServerIronADX(config)# interface ethernet 1/1
ServerIronADX(config-if-1/1)# ip access-group max-l4-cam 50
This command allows up to 50 ACL entries on each port managed by the IPC or IGC that manages
port 1/1.
port 1/1.
Syntax: [no] ip access-group max-l4-cam <num>
The <num> parameter specifies the number of CAM entries and can be from 10 – 2048. The
default depends on the device.
default depends on the device.
The command is valid at the interface configuration level. However, the device applies the change
to all ports managed by the same IPC or IGC. Regardless of the port number, when you save the
change to the startup-config file, the CLI applies the command to the first port managed by the IPC
or IGC. For example, if you enter the command on port 3, when you save the configuration change,
the CLI enters the ip access-group max-l4-cam command under port 1 in the startup-config file.
to all ports managed by the same IPC or IGC. Regardless of the port number, when you save the
change to the startup-config file, the CLI applies the command to the first port managed by the IPC
or IGC. For example, if you enter the command on port 3, when you save the configuration change,
the CLI enters the ip access-group max-l4-cam command under port 1 in the startup-config file.
NOTE
If you enter the command on more than one port managed by the same IPC or IGC, the CLI uses the
value entered with the most-recent command for all the ports on the ICP or IGC.
If you enter the command on more than one port managed by the same IPC or IGC, the CLI uses the
value entered with the most-recent command for all the ports on the ICP or IGC.
Configuring numbered and named ACLs
When you configure ACLs, you can refer to the ACL by a numeric ID or by an alphanumeric name.
The commands to configure numbered ACLs are different from the commands for named ACLs:
The commands to configure numbered ACLs are different from the commands for named ACLs:
•
If you refer to the ACL by a numeric ID, you can use 1 – 99 for a standard ACL or 100 – 199 for
an extended ACL. This document refers to this ACL as numbered ACL.
an extended ACL. This document refers to this ACL as numbered ACL.
•
If you refer to the ACL by a name, you specify whether the ACL is a standard ACL or an extended
ACL, then specify the name. This document refers to this ACL type as named ACL.
ACL, then specify the name. This document refers to this ACL type as named ACL.
You can configure up to 100 standard numbered IP ACLs and 100 extended numbered IP ACLs. You
also can configure up to 100 standard named ACLs and 100 extended named ACLs by number.
Regardless of how many ACLs you have, the device can have a maximum of 4096 ACL entries,
associated with the ACLs in any combination.
also can configure up to 100 standard named ACLs and 100 extended named ACLs by number.
Regardless of how many ACLs you have, the device can have a maximum of 4096 ACL entries,
associated with the ACLs in any combination.