Manual De UsuarioTabla de contenidosContents3Before You Begin91.1 Overview91.2 Safety91.3 Using this manual91.4 Interpreting your model number101.5 Obtaining version information101.6 Communication tools101.7 Flowmeter documentation111.8 Micro Motion customer service11Quick Start132.1 Overview132.2 Configuration overview and flowchart132.3 Configuration worksheet152.4 Menu flowcharts182.4.1 ProLink II menus192.4.2 Communicator menus212.4.3 Display menus25Getting Ready to Configure333.1 Overview333.2 Applying power333.3 Setting up and making an administrative connection343.4 Working with the mA output scale343.4.1 Specifying the mA measurement point343.4.2 Converting between mA output scales353.5 Configuration tips and tricks363.5.1 Write-protection363.5.2 Default values and ranges363.5.3 Restoring factory configuration363.6 Display and reporting options for process variables37Configuring Process Measurement394.1 Overview394.2 Characterizing the flowmeter394.3 Configuring general flow parameters404.3.1 Flow direction404.3.2 Flow damping444.4 Configuring mass flow measurement454.4.1 Mass flow measurement unit454.4.2 Mass flow cutoff464.4.3 Defining a special unit for mass flow464.5 Configuring volume flow measurement474.5.1 Volume flow type474.5.2 Volume flow measurement unit474.6 Describing gas properties for GSV flow measurement494.6.1 Volume or GSV flow cutoff504.6.2 Defining a special unit for volume or GSV flow514.7 Configuring density measurement524.7.1 Density measurement units524.7.2 Density cutoff524.7.3 Density damping534.7.4 Slug flow parameters534.8 Configuring temperature measurement544.8.1 Temperature measurement units544.8.2 Temperature damping554.9 Configuring pressure compensation554.9.1 Pressure correction factors554.9.2 Configuration procedure564.10 Damping574.10.1 Damping and volume measurement584.10.2 Interaction with the Added Damping parameter58Configuring Operational Parameters595.1 Overview595.2 Configuring the display595.2.1 Update period595.2.2 Display language595.2.3 Display variables and display precision605.2.4 Enabling and disabling display functions615.3 Configuring fault handling635.3.1 Status alarm severity635.3.2 Last measured value (LMV) timeout665.4 Configuring sensor parameters665.5 Configuring device parameters67Integrating the Meter with the Control System696.1 Overview696.2 Configuring the mA output696.2.1 Process variable706.2.2 mA output scale (LRV and URV)706.2.3 AO cutoff716.2.4 Added damping726.2.5 mA output fault action and fault value736.3 Configuring digital communications746.3.1 Digital communications fault action756.3.2 Loop current mode756.3.3 PV, SV, TV, and QV assignments766.3.4 Burst mode77Testing and Moving to Production797.1 Overview797.2 Flowmeter zero797.2.1 Preparing for zero807.2.2 Performing the zero procedure807.3 Loop testing837.4 Trimming the milliamp output867.4.1 Basic mA output trim867.4.2 Expanded mA output trim897.5 Using sensor simulation to test, tune, and troubleshoot the system907.6 Backing up and restoring the configuration907.7 Write-protecting the configuration91Operating the Transmitter938.1 Overview938.2 Warm-up delay938.3 Interpreting mA output data938.4 Recording process variables948.5 Viewing process variables948.5.1 With the display948.5.2 With ProLink II958.5.3 With the Communicator958.6 Viewing and acknowledging status alarms958.6.1 About status alarms958.6.2 With the display968.6.3 With ProLink II978.6.4 With the Communicator988.7 Using the totalizers and inventories988.7.1 Viewing current totals for totalizers and inventories988.7.2 Controlling totalizers and inventories100Measurement Performance1039.1 Overview1039.2 Meter validation and calibration1039.2.1 Meter validation and meter factors1039.2.2 Calibration1049.2.3 Comparison and recommendations1049.3 Performing meter validation1059.4 Performing density calibration1069.4.1 Preparing for density calibration1069.4.2 Density calibration procedures1069.5 Performing temperature calibration109Troubleshooting11110.1 Overview11110.2 Guide to troubleshooting topics11110.3 Micro Motion customer service11210.4 Transmitter does not operate11210.5 Transmitter does not communicate11210.6 Zero or calibration failure11210.7 Low power and mA fault action11310.8 Fault conditions11310.9 HART output problems11310.10 I/O problems11410.11 Sensor simulation mode11510.12 Status alarms11510.13 Checking process variables11810.14 Diagnosing wiring problems12110.14.1 Checking the power supply wiring12110.14.2 Checking grounding12110.14.3 Checking the HART communication loop12110.15 Checking the communication device12110.16 Checking the output wiring and receiving device12210.17 Checking slug flow12210.18 Checking output saturation12310.19 Checking the HART address and Loop Current Mode parameter12310.20 Checking the flow measurement configuration12310.21 Checking the characterization12310.22 Checking the calibration12410.23 Checking the test points12410.23.1 Obtaining the test points12410.23.2 Drive gain problems12410.23.3 Low pickoff voltage12510.24 Checking sensor circuitry125Default Values and Ranges131A.1 Overview131A.2 Most frequently used defaults and ranges131Flowmeter Installation Types and Components135B.1 Overview135B.2 Transmitter components135B.3 Terminal diagrams136Model 2200S Display and User Interface137C.1 Overview137C.2 Identifying the components of the user interface137C.3 Removing and replacing the transmitter housing cover138C.4 Using the display, the buttons, and the display menu system138C.4.1 Accessing the display menu system138C.4.2 Entering floating-point values from the display menus139C.5 Codes and abbreviations141Connecting with ProLink II Software143D.1 Overview143D.2 Requirements143D.3 Configuration upload/download143D.4 Connecting from a PC to a Model 2200S transmitter143D.5 ProLink II language146Using the 375 Field Communicator147E.1 Overview147E.2 Communicator device description147E.3 Connecting to a transmitter148E.3.1 Connecting to HART clips148E.3.2 Connecting to a multidrop network149E.4 Using the Communicator with the Model 2200S149E.5 Communicator safety messages and notes149Index151Tamaño: 2 MBPáginas: 158Language: EnglishManuales abiertas