Fujifilm F610 Manuel D’Utilisation

99

98

The image is blurred.

There is speckling on
the image.

The camera does not
emit any sound.

Frame erase does not
erase the frame.

The ERASE ALL
function does not erase
all the frames.

There is no image or
sound on the TV.

When the camera is
connected to a
computer, the
photography or playback
screen appears on the
camera’s LCD monitor.

Nothing happens when
I use the camera
switches.

The camera no longer
works correctly.

i The lens is dirty.
i You photographed scenery with Macro

mode selected.

i You took a close-up shot without

selecting Macro mode.

i You are shooting a subject that is not

suited to autofocusing.

The shot was taken with a slow shutter
speed (long exposure) in a high-
temperature environment.

i The camera volume is set too low.
i The microphone was blocked during

shooting/recording.

i There is something covering the speaker

during playback.

Some frames may be protected.

i An A/V cable was connected during

movie playback.

i The camera is not connected to the TV

correctly.

i “TV” is selected as the TV input.
i The TV volume is turned down.

i The USB cable (included) is not properly

connected to the computer or camera.

i The PC is not switched on.

i Camera malfunction.

i The battery is exhausted.

The camera has suffered an unforeseen
problem.

i Clean the lens.
i Cancel Macro mode.

i Select Macro mode.

i Use AF/AE lock to take the shot.

This is a characteristic of CCDs and does
not indicate a camera fault.

i Adjust the volume.
i Take care not to block the microphone

during shooting/recording.

i Ensure that the speaker is uncovered.

Remove the protection.

i After the movie playback mode is

stopped, connect the camera and TV
correctly.

i Connect the camera and TV correctly.

i Set the TV input to “VIDEO”.
i Adjust the volume.

i Set up the camera and the USB cable

(included) correctly.

i Switch the PC on.

i Briefly remove the battery or disconnect

the AC power adapter. Then reload the
battery or reconnect the AC power
adapter and try again.

i Load a new fully charged battery.

Briefly remove the battery or disconnect
the AC power adapter. Then reload the
battery or reconnect the AC power adapter
and try again. If the error message is still
displayed, contact your FUJIFILM dealer.

eIf you think the camera is faulty, check the following once more.

The self-timer lamp
does not light when
charging the battery.

The self-timer lamp
blinks during charging
and the battery won’t
charge.

No power.

Power cuts out during
operation.

Battery runs out quickly.

No photograph is taken
when the Shutter button
is pressed.

Can’t use the flash to
take pictures.

The flash settings are
restricted and cannot
be selected.

Can only select
“Suppressed Flash”
flash mode.

The “Q” or “5” quality
modes cannot be
selected.

The photographed
image is dark even
though the flash was
used.

i There is no battery in the camera.
i The camera and AC power adapter are

not connected correctly.

i The battery terminals are dirty.

i The battery is faulty or flat.

i The battery is exhausted.
i The AC power adapter plug has come

out of the power outlet.

i The battery is loaded the wrong way

round.

i The battery cover is not closed properly.

The battery is exhausted.

i Camera is being used in extremely cold

conditions.

i The terminals are soiled.

i The battery is flat.

i No xD-Picture Card is inserted.
i The xD-Picture Card is fully recorded.

i The xD-Picture Card is not formatted.
i The  xD-Picture Card contact area is

soiled.

i The xD-Picture Card is damaged.
i The Auto Power Off function has

switched the camera off.

i The battery is exhausted.

i The Shutter button was pressed while

the flash was charging.

i The flash is not popped up.
i The camera is set to Scenery in Scene

Position mode.

i Continuous shooting is selected.

Scene Position mode is selected.

Continuous shooting is selected.

The sensitivity is set to 800 (high-sensitivity
shooting).

i The subject is too far away.

i Your finger was covering the flash/flash

control sensor.

i Load the battery.
i Connect the camera and AC power

adapter correctly.

i Take the battery out briefly and then

reload it.

i Wipe the battery terminals with a clean,

dry cloth.

i Fit a new battery. If the battery still fails

to charge, contact an authorized
FUJIFILM service center.

i Load a fully charged battery.
i Plug the adapter back in.

i Load the battery in the correct direction.

i Close the battery cover properly.

Load a new fully charged battery.

i Put the battery in your pocket or another

warm place to heat it and then load it
into the camera just before you take a
picture.

i Wipe the battery terminals with a clean,

dry cloth.

i Fit a new battery.

i Insert an xD-Picture Card.
i Insert a new xD-Picture Card or erase

some unwanted frames.

i Format the xD-Picture Card.
i Wipe the xD-Picture Card contact area

with a clean dry cloth.

i Insert a new xD-Picture Card.
i Switch the camera on.

i Load a new fully charged battery.

i Wait until charging is completed before

pressing the Shutter button.

i Pop up the flash.
i Select another Scene Position or change

the photography mode.

i Set continuous shooting to “OFF”.

The flash settings are restricted because
the camera settings are tailored to the
scene being shot. Change the
photography mode for a wider range of
flash settings.

Set continuous shooting to “OFF”.

In the Photography menu, set the
sensitivity to 400 or less.

i Move to within the effective flash range

before taking the shot.

i Hold the camera correctly.