Outback Power Systems Outback Power Systems Manuel D’Utilisation

Page de 57
Installation & Programming Manual
                    
FX & VFX “E” Series Inverter/Charger System          
Copyright 2003  
  OutBack Power Systems, Inc. 
 
 
                                                                                     19009 62
nd
 Ave NE, Arlington   WA 98223 USA                     
Page 44                                         
Rev 7.0       07/02/04                                                                    Tel 360 435 6030     Fax 360 435 6019  
MATE - ADVANCED MENU 
 
The ADVANCED (ADV) menu section allows adjustment of all the settings involved with the operation of the FX.  Changes made to 
these settings are stored internally in non-volatile memory inside of the FX – the settings are not lost when the MATE is removed or 
battery power is disconnect.   
Some settings appear both in the SETUP and in the ADV menus.  Changes made to these settings in one area will cause the same 
changes to occur in the other area.  The settings are provided in both menus to make it more convenient for the FX programmer by 
giving access to all of the settings in the advanced menu.   
Access to the settings in the ADV menu is restricted through the use of a password.  This password is required to view and adjust the 
settings.  Once the password has been entered, all advanced categories can be adjusted without having to re-enter the password.  If 
the advanced menu is exited and re-entered, the password must be re-entered, however.  Use of the “hot” keys AC IN and INV is 
allowed from the advanced menu and selecting OK from these screens will return you to the same point in the advanced menu.  
The password for the inverter is currently fixed to the same value for all of the FX’s. 
 
PASSWORD CODE:
  
1 4 1 
 
 
MAIN---------------- 
6:54:42P 
 
SUM STATUS SETUP ADV 
                  
↓ 
ADV/SETTINGS/WARNING 
changes made could 
adversely effect 
system performance 
 
↓     ↓     ↓    ↓ 
ADV/PASSWORD-------- 
 enter the password: 
        132 
ENTER INC  DEC  EXIT 
 
↓ 
ADV----------------- 
choose product: 
 
FX    MX  MATE  MAIN 
 
↓ 
ADV/FX/PAGE1-------- 
choose category: 
 
ADV  INV  CHGR  PG2 
                  
↓ 
ADV/FX/PAGE2-------- 
choose category: 
 
PG1  GRID   GEN  PG3 
                  
↓ 
ADV/FX/PAGE3-------- 
choose category: 
 
PG2  AUX  STACK  PG4 
                  
↓ 
ADV/FX/PAGE3-------- 
choose category: 
 
PG3  SELL  CAL  MAIN 
The MAIN screen is where the menu system starts.  The four words in the bottom line of the 
display correspond to the four buttons located below the display. The word in BOLD on the bottom 
line indicates the selection used to advance the display to the next screen.  Pressing the left two 
buttons simultaneously from anywhere in the menu will return you to this screen. 
 
Selecting <ADV> brings up a warning message.  Please read the message.  Pressing any of the 
four keys below the display advances the display to the password screen.   
 
 
Entering the correct password
 number is done by pressing the <INC> key to increase the 
number or the <DEC> key to decrease the number.   Once the number shown matches the 
password code, press the key below the word <ENTER>.  To leave the advanced menu area 
without making any changes, press EXIT.   
 
Following the password screen is a screen that allows selection of the OutBack product type.  
Selecting <FX> allows adjustment of the FX’s advanced programming.  Selecting MX will allow 
access to the advanced sections of any MX-60’s connected to the system (through a HUB).  
Selecting MATE will allow access to the MATE’s advanced screens.  Selecting MAIN returns the 
user to the MAIN menu.  
 
 
There are eight categories of settings in the FX: 
INV
 
Allows adjustment of the INVERTER settings and operation 
CHGR
 
Allows adjustment of the CHARGER settings and operation 
GRID
 
Allows adjustment of the AC input settings and operation if the FX’s input is set to GRID 
GEN
 
Allows adjustment of the AC input settings and operation if the FX’s input is set to GEN 
AUX 
 
Allows adjustment of the AUX OUTPUT settings and operation 
STACK 
Allows adjustment of the master/slave settings for multi-FX systems  
SELL
 
Allows adjustment of the Grid-Tie settings and operation 
CAL
 
Allows adjustment of the voltage calibration measurements to improve operation 
 
Selecting ADV will send the user back one screen to the “choose product” screen in the advanced 
menu.  PG2 will advance the user to page 2 of the advanced menu.  PG3 will advance the user to 
page 3 of the advanced menu.  PG4 will advance the user to page 4 of the advanced menu.  
Selecting MAIN will return the user to the MAIN screen.