Fujifilm s5000 Manuel D’Utilisation
13
Getting Ready
◆
Checking the remaining battery charge
◆
●
!
The information above is an approximate guide for photography mode. Depending on the camera mode and the type
of batteries used, the transition from “
of batteries used, the transition from “
C
” to “
V
” may occur more quickly.
●
!
When the batteries runs flat, “
V
” is displayed and camera operation automatically stops. When this occurs, the
camera may work if you switch it on again even without loading new or fully charged batteries. However, this may
cause camera faults such as the camera switching itself off without retracting the lens. Always load new or fully
charged batteries.
cause camera faults such as the camera switching itself off without retracting the lens. Always load new or fully
charged batteries.
●
!
Due to the nature of the battery, the battery low warning may appear early when the camera is used in cold locations.
This is normal and does not indicate a fault. Try warming the batteries in your pocket or a similar location before use.
This is normal and does not indicate a fault. Try warming the batteries in your pocket or a similar location before use.
“
C
” is displayed as a small icon on the right-hand
side of the screen. “
V
” appears as a large icon in
the center of the screen.
Switch the camera on and check that no battery level warning (
C
or
V
) is displayed on the screen.
If no icon is displayed, there is ample charge left in the batteries.
1 There is ample remaining battery charge.
2 The battery charge is low. Have a new set of
2 The battery charge is low. Have a new set of
batteries ready.
3 The batteries are exhausted. The display will
shortly go blank and the camera will stop working.
Replace or recharge the batteries.
Replace or recharge the batteries.
Blinking red
Lit red
1
2
3
No icon
12
2
Indicator
Indicator
1
3
Align the indicators on the xD-Picture Card slot and
xD-Picture Card and then push the card firmly all
the way into the slot.
xD-Picture Card and then push the card firmly all
the way into the slot.
●
!
The xD-Picture Card will not slide fully into the slot if it is
inserted facing the wrong way. Be careful not to apply undue
force to the xD-Picture Card.
inserted facing the wrong way. Be careful not to apply undue
force to the xD-Picture Card.
Close the slot cover.
◆
When you want to replace the xD-Picture Card
◆
Ensure that the camera is switched off before
opening the slot cover. When the xD-Picture Card is
pushed into the slot and then slowly released, the
card lock releases and the xD-Picture Card is
pushed out.
opening the slot cover. When the xD-Picture Card is
pushed into the slot and then slowly released, the
card lock releases and the xD-Picture Card is
pushed out.
LOADING THE MEDIA
Set the Power switch to “OFF”, check that the
indicator lamp is off and then open the slot cover.
indicator lamp is off and then open the slot cover.
●
!
If you open the slot cover while the camera is still switched
on, the camera is switched off as a safety measure.
on, the camera is switched off as a safety measure.
◆
Power save function
◆
When this function is active, it also switches off the LCD monitor to reduce power consumption if the
camera is not used for 30 seconds (See P.75 for details). If the camera is then left unused for a further
period (2 minutes or 5 minutes), the Power save function automatically switches the camera off. To
switch the camera back on, turn the Power switch to turn the camera off briefly and then turn it back on.
camera is not used for 30 seconds (See P.75 for details). If the camera is then left unused for a further
period (2 minutes or 5 minutes), the Power save function automatically switches the camera off. To
switch the camera back on, turn the Power switch to turn the camera off briefly and then turn it back on.
充電池放電中
充電池放電中
ＡＵＴＯ
ＡＵＴＯ
３３
３３
ＡＵＴＯ
ＡＵＴＯ
３３
３３
Lit red
Blinking red