Fujifilm A202 Manuel D’Utilisation

Software needed for playing back movies, etc.

Launches the FinePixViewer 
software when a camera is 
connected.

Software used to read PDF-format documents on a personal computer. This software is needed to read the 
User’s Guides for FinePixViewer (Macintosh only).

Creates a FinePix CD Album 
(Mac OS X is not supported).

“Used when you open 
RAW files that were 
photographed on cameras 
that support the RAW file 
format.”

Allows you to display thumbnail lists of the images 
stored on your PC or in the camera, print the 
images individually or as an index, display the 
images at full size and perform some basic image 
processing.

✽ Note that the software configuration differs slightly depending on your operating system.

Connect the camera 
with “DSC” selected as 
the USB setting 
(

➡P.87). 

Allows a digital camera to be used 
as USB Mass Storage (removable 
disk drive, card reader).

6.1 The Software Components

ＳＥＴーＵＰ

ＳＥＴーＵＰ

１／２

１／２

ＩＭＡＧＥ ＤＩＳＰ．

ＩＭＡＧＥ ＤＩＳＰ．

ＯＮ

ＯＮ

ＯＮ

ＯＮ

ＰＯＷＥＲ ＳＡＶＥ

ＰＯＷＥＲ ＳＡＶＥ

ＤＡＴＥ／ＴＩＭＥ

ＤＡＴＥ／ＴＩＭＥ

ＳＥＴ

ＳＥＴ

ＬＣＤ

ＬＣＤ

ＯＮ

ＯＮ

ＢＥＥＰ

ＢＥＥＰ

ＬＯＷ

ＬＯＷ

ＯＫ

ＯＫ

ＢＡＣＫ

ＢＡＣＫ

hPower saving “ON” (default setting)
Power consumption is kept to a minimum to
prevent battery depletion. Select the “ON”
setting when you are using alkaline batteries.

iIf the camera is not used for approximately 30

seconds, the LCD switches off temporarily to reduce
power consumption (Sleep mode).

iOnce the camera is in Sleep mode, if it is left

unused for a further 90 seconds, it is automatically
switched off.

iThe charging time for the flash increases slightly

because the flash charging power is reduced.

hPower saving “OFF”
Batteries are more likely to run flat since no
power reduction measures (sleep mode, etc.)
are used. However, this function automatically
switches the camera off if the camera is not
used for approximately 2 minutes.

To bring the camera out of sleep mode so that it
is ready to shoot, press “d”, “c”, “a” or “b”.
This is useful since the camera is ready to shoot
more quickly than when it is switched off and
then on again. You can also take pictures when
the camera is in sleep mode simply by pressing
the shutter button.

●

Power Save/Auto Power Off does not function when
a USB connection is being used.

●

You can also bring the camera out of sleep mode by
pressing buttons other than “d”, “c”, “a” or “b”.

●

To switch the camera back on, briefly switch the
camera off and then on again.

The Sleep function does not operate when the
LCD monitor is switched off, while you are
setting the quality mode or when the camera is
in SET–UP or Playback mode. However, if the
camera controls are not used for 2 minutes, the
camera automatically switches off.

g POWER SAVE