Fujifilm A203 Manuel D’Utilisation
88
89
7
■ Camera Operation
i When the camera and computer are exchanging
data, the self timer lamp flashes and the
viewfinder lamp flashes alternately green and
orange.
viewfinder lamp flashes alternately green and
orange.
i “DSC” appears on the screen.
i Power Save and Auto Power Off are disabled
i Power Save and Auto Power Off are disabled
during USB connection.
✽Before replacing the xD-Picture Card, always
disconnect the camera from the PC using the
procedure on P.94.
procedure on P.94.
✽Do not disconnect the USB cable when the camera is
communicating with the PC. See P.94 for information
on the disconnection procedure.
on the disconnection procedure.
■ PC Operation
✽ The Windows CD-ROM may also be required
during installation. In this event, switch CD-ROMs
as directed by the on-screen instructions.
as directed by the on-screen instructions.
i FinePixViewer automatically starts up.
Windows 98/98 SE/Me/2000 Professional
i A removable disk icon appears and you can
use your PC to transfer files to and from the
camera.
camera.
Windows
Macintosh
✽ Screen for
Windows 98 SE
If the above operations do not occur, you do not
have the required software programs or drivers
installed on your PC. Complete the required PC
setup procedures. Then reconnect the camera
to your PC.
have the required software programs or drivers
installed on your PC. Complete the required PC
setup procedures. Then reconnect the camera
to your PC.
AC power
adapter
adapter
✽
Camera
(USB) socket
USB
socket
socket
PC
ＤＡＴＥ／ＴＩＭＥ
ＤＡＴＥ／ＴＩＭＥ
ＵＳＢ ＭＯＤＥ
ＰＯＷＥＲ ＳＡＶＥ
ＰＯＷＥＲ ＳＡＶＥ ＯＮ
ＯＮ
ＰＯＳＴＶＩＥＷ ＯＮ
ＯＮ
ＳＥＴ
ＳＥＴ
ＤＳＣ
ＤＳＣ
ＤＳＣ
ＤＳＣ
ＤＳＣ
ＳＥＴ−ＵＰ
ＳＥＴ−ＵＰ
ＢＡＣＫ
ＢＡＣＫ
ＢＡＣＫ
ＯＫ
ＯＫ
ＯＫ
1. Load an xD-Picture Card containing
photographed images into your camera. Plug
the AC power adapter connector into the DC
IN 3V socket on the camera and then plug
the adapter itself into the main power outlet.
the AC power adapter connector into the DC
IN 3V socket on the camera and then plug
the adapter itself into the main power outlet.
2. Slide the power switch to the side to turn
the camera on.
3. Set the “USB MODE” setting in the
“SET–UP” menu to “DSC” (
➡P.72, 73).
4. Slide the Power switch to the side to turn
the camera off.
5. Switch your PC on.
6. Use the special USB cable to connect the
6. Use the special USB cable to connect the
camera to your computer.
7. Switch the camera on.
Always use the prescribed procedure when
disconnecting or switching off the camera
(
disconnecting or switching off the camera
(
➡P.94).
If you are using a Windows PC, the driver settings
are specified automatically when installation is
completed. No further action is required.
are specified automatically when installation is
completed. No further action is required.
✽On Windows XP and Mac OS X, you must specify the
automatic launch settings the first time you connect
the camera to your computer.
the camera to your computer.
✽Take care to ensure that the special USB cable is
connected the correct way around and that the plugs
are pushed fully into the connection sockets.
are pushed fully into the connection sockets.
7.2 Use at DSC mode
✽ Sold separately
✽It is recommended that you connect the AC Power
Adapter AC-3V (sold separately) (
➡P.87). Constant
power supply will prevent successful data transfer
from trouble caused by power supply.
from trouble caused by power supply.