Bakers Pride 101 Manuel D’Utilisation
G. LEAK TESTING:
·
The plumbing must now be tested for gas leaks before use. Turn all propane tank, burner control and
carryover control valves to the OFF position. Wet all gas line fittings and connectors with a solution of soapy water (or
commercial leak disclosing liquid). Slowly open the propane tank valve(s) and look for bubbles of foam at any of the
joints of the system. If a leak is found, close the tank valves immediately and call your local dealer or the manufacturer.
If the gas connections are leak-free, the unit is ready to use. Follow the lighting instructions.
commercial leak disclosing liquid). Slowly open the propane tank valve(s) and look for bubbles of foam at any of the
joints of the system. If a leak is found, close the tank valves immediately and call your local dealer or the manufacturer.
If the gas connections are leak-free, the unit is ready to use. Follow the lighting instructions.
Side Rack Installation:
!
Side racks have to be installed on both sides of the 60" stand and on the right side of the 30" stand if your
unit came with 20 lb LP cylinders. Optional 40 lb horizontal cylinders come with single or double tank
caddy.
unit came with 20 lb LP cylinders. Optional 40 lb horizontal cylinders come with single or double tank
caddy.
!
Attach the tank rack to the side of the stand with two 1/4-20" thumb screws provided (see fig. A-1). Make
sure the screws are properly tightened.
sure the screws are properly tightened.
!
Clamp mounting bracket to the legs with the clamps and fasten with (2) thumb screws.
!
Hang the 20lb cylinder on the rack with service valve outlet facing the front of the unit (see fig. A-2)
!
Fasten the tank with tank brace and wingnut.
!
Make sure the tanks are secure in their racks and can not move
2. LIGHTING INSTRUCTIONS
A. LIGHTING INSTRUCTIONS: Fill water pans to within ½" of top edges (this will control grease flare-ups, provide for
ease of cleaning and keep cooked food moist). Re-fill pans with water when they evaporate to within ½" of the bottom
of the pans. Failure to keep water in the water pans could lead to grease fires and will void the warranty.
ease of cleaning and keep cooked food moist). Re-fill pans with water when they evaporate to within ½" of the bottom
of the pans. Failure to keep water in the water pans could lead to grease fires and will void the warranty.
1.
Check that the tank mounting brackets are securely mounted on the unit.
2.
Open the roll-up hood if so equipped. Turn all the burner knobs and carryover tube knobs to the OFF position
and slowly open the gas tank valves.
and slowly open the gas tank valves.
3.
Turn the carryover tube knob on one side fully counter-clockwise to the ON position. Insert a lit, extra long
match or a gas lighter flame though the hole on the same side in the front panel. For 60” broilers repeat the
same procedure for the other side.
match or a gas lighter flame though the hole on the same side in the front panel. For 60” broilers repeat the
same procedure for the other side.
4.
Check that the entire crossover tube is lit by looking through the lighter hole(s) located on the front panel. If the
carryover tube(s) will not light or stay lit, shut off the gas supply and do not use the unit. Wait 5 minutes before
attempting to re-light the unit. (See Figure “B”)
5.
After lighting the crossover tube(s), open the desired burner valves and observe that the burners light
completely from the crossover tube(s).
completely from the crossover tube(s).
iqqqqqq
F. INSTALLING OPTIONAL TANK CADDY:
!
If you unit is equipped with optional
tank caddy, it has to be placed
underneath the broiler and secured
in place by (2) hooks provided (see
fig. “A-3”). The front of the caddy will
be raised off the ground to prevent
possible movement and putting
strain on connection hoses.
tank caddy, it has to be placed
underneath the broiler and secured
in place by (2) hooks provided (see
fig. “A-3”). The front of the caddy will
be raised off the ground to prevent
possible movement and putting
strain on connection hoses.
!
LP gas cylinder(s) have to be
securely mounted to the caddy with
thumb screws. They will only work in
the horizontal position.
securely mounted to the caddy with
thumb screws. They will only work in
the horizontal position.
Figure “A-3”
Black Plastic
Connector
Tank Caddy (Single)
Hook
5