Bunn ICB Mode D'Emploi
Page 24
PROGRAMMING THE BREWER (cont.)
PROGRAMMING FUNCTIONS - LEVEL 2 (cont.)
37077 071206
release DONE. The display should read 2 BATCHES
DONE?
DONE?
16. If both batch sizes are not correct press and release
NO to return to the %BYPASS function and repeat
steps #13, 14 and 15.
steps #13, 14 and 15.
17. If both batch sizes are correct, press YES. This will
advance to the SET PULSE BREW function (Refer
to page 28 for description of SET PULSE BREW
function.
to page 28 for description of SET PULSE BREW
function.
18. To SET PULSE BREW press YES and proceed with
the setup instructions for SETTING PULSE BREW,
on page 29.
on page 29.
19. To skip setting the PULSE BREW and to use the
FACTORY DEFAULTS, press NO to proceed to the
DRIP TIMES function.
DRIP TIMES function.
20. The display should now read DRIP TIME, along with
either the word OFF or a time showing. A batch light
will also be blinking.
will also be blinking.
21. Using (-) and (+), set the amount of time from when
the brew spray ends to when the funnel is emptied
of hot liquid.
of hot liquid.
22. When fi nished, press the other batch size and repeat
step #21.
23. When fi nished setting both batch sizes, press and
release DONE. The display should read 2 BATCHES
DONE?
DONE?
24 Press and release YES. The screen should show the
name of the coffee being programmed (modifi ed)
along with SETUP COMPLETE.
along with SETUP COMPLETE.
25. After a 5 second delay, the display will advance to
the next coffee name in the brewer’s memory. If
no other coffee names are present, the display will
read THAT WAS THE LAST RECIPE, and advance
to the SET TEMP screen.
no other coffee names are present, the display will
read THAT WAS THE LAST RECIPE, and advance
to the SET TEMP screen.
SET NEW RECIPE
Using a RECIPE CARD to load coffee names and brew
settings
The G9-2T DBC or MHG Grinder’s memory contains
certain coffee names. If the operator uses a coffee name
that is not already stored in the grinder’s memory, a
RECIPE CARD can be obtained from the factory. The
RECIPE CARD would include all the information needed
to set up that particular coffee name. The information
from the RECIPE CARD is loaded into the grinder’s
Using a RECIPE CARD to load coffee names and brew
settings
The G9-2T DBC or MHG Grinder’s memory contains
certain coffee names. If the operator uses a coffee name
that is not already stored in the grinder’s memory, a
RECIPE CARD can be obtained from the factory. The
RECIPE CARD would include all the information needed
to set up that particular coffee name. The information
from the RECIPE CARD is loaded into the grinder’s
memory, then into the brewer’s memory by holding
the chip area up to the equipment’s SENSING COIL.
This information can include the coffee name, BREW
VOLUMES, PULSE BREW TIMES and DRIP OUT TIME
for that particular coffee name. These can all be loaded
in seconds.
the chip area up to the equipment’s SENSING COIL.
This information can include the coffee name, BREW
VOLUMES, PULSE BREW TIMES and DRIP OUT TIME
for that particular coffee name. These can all be loaded
in seconds.
Contact Bunn-O-Matic Corporation for the availability
of RECIPE CARDS and the RECIPE WRITER used to
program the RECIPE CARDS.
NOTE: Instructions to program the brewer and grinder
are printed on the RECIPE CARD, along with the coffee
name that is being programmed.
of RECIPE CARDS and the RECIPE WRITER used to
program the RECIPE CARDS.
NOTE: Instructions to program the brewer and grinder
are printed on the RECIPE CARD, along with the coffee
name that is being programmed.
Procedure to program the coffee name:
1. Remove the funnel (if present) from the funnel
1. Remove the funnel (if present) from the funnel
rails.
2. Position the RECIPE CARD vertically, so that the
top end of the CHIP is beneath the SENSING COIL
(located on the middle of the underneath side of
the front display panel).
(located on the middle of the underneath side of
the front display panel).
3. After a short pause the display will read CARD CON-
TAINS RECIPE FOR then will change to (COFFEE
NAME) SHOW QUIT SAVE. All brewing parameters
for that coffee fl avor are now transferred from the
CARD to the brewer.
NAME) SHOW QUIT SAVE. All brewing parameters
for that coffee fl avor are now transferred from the
CARD to the brewer.
4. To show (view) this information, press and release
SHOW. The display will scroll through all of the
brew settings for that recipe. This display will then
return to CARD CONTAINS RECIPE FOR then will
change to (COFFEE NAME) SHOW QUIT SAVE.
brew settings for that recipe. This display will then
return to CARD CONTAINS RECIPE FOR then will
change to (COFFEE NAME) SHOW QUIT SAVE.
5. If all brew settings are correct, press SAVE. The dis-
play will read (COFFEE NAME) SETUP COMPLETE.
All brew settings for that name are now stored in
the brewer’s memory.
All brew settings for that name are now stored in
the brewer’s memory.
6. If the brewing information is not correct, or it is
desired to exit the setup before the settings are
loaded into the brewer’s memory, press QUIT. The
display will read (COFFEE NAME) NOT SAVED. The
display will then return to the MAIN SCREEN.
loaded into the brewer’s memory, press QUIT. The
display will read (COFFEE NAME) NOT SAVED. The
display will then return to the MAIN SCREEN.