OmniTek OP10 Manuel D’Utilisation

TABLE 1: WIRE GAGE SPECIFICATIONS

SPECIFICATIONS

Electrical Characteristics:

Distance

Gage

5 Conductor

6 Conductor

≤ 200 ft. (61m)

Alpha 1295C

Alpha 1296C

≤300 ft. (91m)

Alpha 58126

≤ 500 ft. (153 m)

Alpha 58136

Note: Recommended cable is only a guideline, use any

manufacturer that meets the gage and shield specifications.

Power Supply Type:

Linear type Recommended

Operating Voltage Range:

5.0 – 16 VDC (Operational down to 4.25 VDC)

Maximum input current:

OP10, OP20, OP90

Standby: 35 mA
Read: 50 mA

OP30, OP40, OP45

HOW TO TEST AND OPERATE THE READER

Standby:

The reader should be tested after wiring it to a power supply

and the host. Do this by performing the following steps:

Read:

100

Tamper Output

Open collector, active low, max.sink current is 16 mA

1. Power up the reader. The LED and beeper will

activate three times. This indicates that the

reader is working properly.

Maximum Cable Distance to Host:

500 ft. (150 meters)

2. Present the appropriate type of ID card to the

reader. (See Table 2 for the correct card type

based on the reader model.) The LED will

momentarily flash green and a short beep will be

emitted. This indicates that the card was read

properly by OmniProx.

Card Read Distance:

See Table 2

Regulatory Approvals:

USA: UL 294 Listed & FCC Part 15 B

(Model OP90 is not yet UL listed)

Europe: CE Listed

3. After the card data is processed by the host, the

host can then turn the LED green or yellow.

Refer to the host description of the LED

operation if the reader LED is controlled by the

host.

Operating Temperature Range:

-25° F to 145° F (-31°C to 63°C)

Operating Humidity:

0 to 95% (non condensing)
Suitable for outdoor use

Dimensions:

OP10:

Table 2: Model Number vs. Feature Matrix

3.15” (80mm) L x 1.58” (40mm) W x 0.50” (12.8mm) D

Model

Number

UL Listing

Part #

Card

Type

Output

Format

Read

Range

(Max.) *

OP10-FW AY-K10  HID  Wiegand  3”
OP20-FW AY-J10  HID  Wiegand  4”
OP30-FW AY-L10  HID  Wiegand  5”
OP40-FW AY-H10  HID  Wiegand  4”
OP45-FW AY-M10  HID  Wiegand  4”
OP90-FW AY-Q10  HID  Wiegand  1.5”

Measured using HID Corp. Prox Card II (P/N 1326LSSMV)

or equivalent and the corresponding OmniProx reader

powered at 12 volts. Range also depends on electrical

environment and/or proximity to metal.

OP20:

4.73” (120mm) L x 1.65” (42mm) W x 0.55” (14mm) D

OP30:

5.71” (145mm) L x 1.69” (43mm) W x 0.79” (20mm) D

OP40:

4.33” (110mm) L x 2.96” (75mm) W x 0.59” (15mm) D

OP45:

3.5” (89mm) L x 3.5” (89mm) W x 0.59” (15mm) D

OP90:

4.72” (120mm) L x 3” (76mm) W x 1” (27mm) D

For additional information on the Wiegand™ Protocol, see
“Access Control Standard – Wiegand Card Reader Interface
SIA AC-01 (1996.10)” which can be purchased from SIA (see
www.siaonline.org)

OmniProx models with HID
compatibility are capable of reading
genuine HID cards under the terms of
a license agreement between HID
Corp. and the ADEMCO Group.

-2-