CipherLab Co. Ltd. 11661 Manuel D’Utilisation
13
4.2 RS232 Interface
User can select the desired, flow control, baud rate, parity, and data bits to be used
in this output interface.
in this output interface.
4.2.1 Baud Rate / Parity / Data Bits
The supported baud rate, parity, and data bit are listed below.
The supported baud rate, parity, and data bit are listed below.
• Baud Rate: 115200 / 38400 / 19200 / 9600 / 4800 / 2400 / 1200 / 600
• Parity: None / Even / Odd
• Data bit: 8 / 7
• Parity: None / Even / Odd
• Data bit: 8 / 7
4.2.2 Flow Control
The user can further configure the flow (handshake) control method to be used.
The available options are listed below.
The user can further configure the flow (handshake) control method to be used.
The available options are listed below.
• No Flow Control
• Scanner Ready: The scanner will activate the RTS signal after power on.
• Scanner Ready: The scanner will activate the RTS signal after power on.
After each good read the scanner waits for an active CTS signal. The data
will not be sent until CTS signal becomes active.
will not be sent until CTS signal becomes active.
• Data Ready: The RTS signal will be activated after each good read. The
scanner will then wait for the CTS signal becomes active. The data will not
be sent until CTS signal becomes active.
be sent until CTS signal becomes active.
• Inverted Data Ready: It is like the Data Ready flow control, but the RTS
signal level is inverted.
4.2.3 Inter-Character Delay
An inter-character delay of 0 to 255 ms can be configured to match the computer
response time. The delay time configured is inserted between transmitting every
character. The longer the delay time configured, the slower the transmission speed
will be. The inter-character delay is zero by default.
An inter-character delay of 0 to 255 ms can be configured to match the computer
response time. The delay time configured is inserted between transmitting every
character. The longer the delay time configured, the slower the transmission speed
will be. The inter-character delay is zero by default.
4.3 USB Interface
A USB interface is also available. For installation instructions please refer to the
separate diskette included with your scanner.
separate diskette included with your scanner.
4.4 Memory Parameters
The 1166P/1266P reserves 4 KB flash memory as transmit buffer when the scanner
is out of service range. Data will be saved into the reserved buffer when the
is out of service range. Data will be saved into the reserved buffer when the
14
scanner is out of signal range and data will transmitted to server when the scanner
is back to the service range.
is back to the service range.
The 1166P/1266P can work offline and store the reading data into the internal
Flash memory for later upload to the host. The stored data can be up to 128Kbytes.
Flash memory for later upload to the host. The stored data can be up to 128Kbytes.
4.4.1 Transmit Buffer Setting
Please enable the transmit buffer by scanning transmit buffer setting ENABLE
label. Disable the manual memory function by scanning the DISABLE transmit
buffer setting.
Please enable the transmit buffer by scanning transmit buffer setting ENABLE
label. Disable the manual memory function by scanning the DISABLE transmit
buffer setting.
4.4.2 Memory Mode
Please enable the manual memory function by scanning the memory mode
ENABLE label. Disable the manual memory function by scanning the DISABLE
memory mode label.
Please enable the manual memory function by scanning the memory mode
ENABLE label. Disable the manual memory function by scanning the DISABLE
memory mode label.
4.4.3 Clear Data
The CLEAR label will enable the user to CLEAR or ERASE the data in the
scanner’s memory. The user must also scan the CONFIRM label immediately after
the CLEAR label.
The CLEAR label will enable the user to CLEAR or ERASE the data in the
scanner’s memory. The user must also scan the CONFIRM label immediately after
the CLEAR label.
4.4.4 Send Data
This enables the user to transmit the data in the scanner’s memory to the host. The
interface selected by the user will be used for the transmission. During the
transmission the red LED of 1166P/1266P will be flashing.
This enables the user to transmit the data in the scanner’s memory to the host. The
interface selected by the user will be used for the transmission. During the
transmission the red LED of 1166P/1266P will be flashing.
4.4.5 Memory Data Delay
This will enable the user to set a delay between each data records in memory at
time of transmission.
This will enable the user to set a delay between each data records in memory at
time of transmission.