Tunturi C40 Manuel D’Utilisation

 The 

 display will start to flash. Set the desired 

heart rate value (default 110 bpm) by using the arrow 
keys. Press 

 

The preset value can be 

changed during the training.

 The

 display will start to flash. Choose the 

desired duration of workout by using the arrow keys 
(10-90 minutes in steps of 5 minutes). Press 

. 

The equipment uses this value to calculate the duration 
of the different effort levels during the program.

 The Total Counts display starts to flash. The display 

reads 

 _. Enter your weight using the arrow keys 

(default value 70 kg). Press 

.

 Begin your workout. If the set heart rate value seems 

too strenuous or easy, change the heart rate value by 
using the arrow keys. The columns in the display show 
the present heart rate level.

The values in a workout that has been interrupted are 
saved in the memory of the meter for 5 minutes, after 
which they are 

. You can restart the interrupted 

exercise by pedaling within 5 minutes.

Please follow these instructions when carrying and 
moving the equipment about, because lifting it 
incorrectly may strain your back or risk other accidents: 

Always switch the power off and unplug the 

power cord before you start moving the equipment 
around! 

The device is easy to move by pushing along on the 
integrated transport wheels. Tilt the device from the 
front and push along the floor on the wheels at the front 
support.

To prevent the equipment malfunctioning, store in a dry 
place with as little temperature variation as possible and 
protected from dust. 

The equipment requires very little maintenance. Check, 
however, from time-to-time that all screws and nuts are 
tight. 

 After exercising, clean the equipment with a soft, 

absorbent cloth. Do not use solvents. Sweat may cause 
corrosion: we recommend therefore that you protect all 
metal surfaces outside the plastic covers with teflon.

 Never remove the equipment’s protective casing. 

 If the equipment is not used for a period of time, the 

transmission belt may become temporarily distorted. 
This can lead to a sensation of slightly uneven pedaling. 
However, after a few minutes of use the effect disappears 
as the belt returns to its original form.

 Despite continuous quality control, defects and 

malfunctions caused by individual components may 
occur in the equipment. In most cases it’s unnecessary 

to take the whole device in for repair, as it’s usually 
sufficient to replace the defective part. Always  give 
the model, serial number of your equipment and in 
case of malfunctions also conditions of use, nature of 
malfunction and any error code. 

When you encounter unusual behavior from the device, 
simply turn the power off, wait 1 minute and turn the 
power on. This should clear incidental errors and ready 
the device for normal operation again. If after you have 
reset the device by turning the power off and on again, 
and the device is still not operational, contact your local 
Tunturi dealer for service.

If you require spare parts, always give the model, serial 
number of your equipment and the spare part number 
for the part you need. The spare part list is at the back 
of this manual. Use only spare parts mentioned in the 
spare part list.

Length..........................................146 cm
Width ..........................................65 cm 
Height..........................................157 cm
Weight .........................................68 kg

The C40 meets the requirements of the EU’s EMC 
Directives on electromagnetic compatibility (89/336/
EEC) and electrical equipment designed for use within 
certain voltage limits (73/23/EEC). This product 
therefore carries the CE label. 

The North American versions (115 V) comply with 
FCC requirements on electromagnetic compatibility 
and are accordingly marked with the FCC label. The 
North American versions also comply with the following 
safety standards: UL 1647 and CSA C 22.2 No. 68-92. 

The C40 crosstrainer meets EN precision and safety 
standards (Class A, EN-957). 

Due to our continuous policy of product development, 
Tunturi reserves the right to change specifications 
without notice. 

The instructions must be followed carefully in 

the assembly, use and maintenance of your equipment. 
The warranty does not cover damage due to negligence 
of the assembly, adjustment and maintenance 
instructions described herein. Changes or modifications 
not expressly approved by Tunturi Oy Ltd will void the 
user’s authority to operate the equipment! 

Tunturi_C40   9

7.1.2005, 15:13:07