Geemarc Clearview Cordless Caller Display Unit Fascicule
Introduction
Thank you for choosing Geemarc’s Clearview Cordless Caller Display.
Please read the instructions carefully before use and keep this User Guide for future
Please read the instructions carefully before use and keep this User Guide for future
reference.
The Clearview stores up to 60 names and numbers in its call list. The display is extra
The Clearview stores up to 60 names and numbers in its call list. The display is extra
large, allowing you to read it from across the room, without the need to walk to the
display.
Also it serves as a jumbo LCD clock, which never has to be set, since it is set
Also it serves as a jumbo LCD clock, which never has to be set, since it is set
automatically by the caller ID information.
The Clearview can also hold a directory of 50 names and numbers. If an incoming
The Clearview can also hold a directory of 50 names and numbers. If an incoming
number matches a record, the assigned name (such as FATHER, OFFICE, etc) will be
mapped and shown on the display. You can build up your own directory.
The Clearview can cover a range of up to 20 metres from the base in a typical household
The Clearview can cover a range of up to 20 metres from the base in a typical household
environment.
Note - Consult your PABX supervisor before fitting this product to a PABX facility.
Note - Consult your PABX supervisor before fitting this product to a PABX facility.
Caller Display service
Your Clearview Cordless Caller Display receives and displays caller information,
which is transmitted over the BT network or other network providers. The information
will include the date and time the call is received. And in most cases the caller’s phone
number.
Note -To enable your Clearview Cordless Caller Display to display information transmitted
Note -To enable your Clearview Cordless Caller Display to display information transmitted
via BT or other UK network providers you will first have to subscribe to that networks
Caller Display Service. Please contact your network service provider to arrange this
service.
Installation
Position your Clearview Cordless Caller ID Base Unit within 2 metres of a telephone
socket.
Do not stand your Clearview Cordless Caller ID display or Base Unit on carpets or
Do not stand your Clearview Cordless Caller ID display or Base Unit on carpets or
other similar surfaces which might generate fibres. Do not expose the units to high
temperatures by siting near radiators etc. Keep the units dry and do not operate in
outdoor conditions.
Do not cover or enclose the machine. Allow a free flow of air to its surfaces.
NOTE: We advise that the units be placed on a table cloth or similar, as rubber feet can
outdoor conditions.
Do not cover or enclose the machine. Allow a free flow of air to its surfaces.
NOTE: We advise that the units be placed on a table cloth or similar, as rubber feet can
mark some surfaces.
Connect the adaptor to the base unit
Plug the adaptor into the mains socket and connect the small plug into the 9vAC/DC
socket at the rear of the Clearview base unit. Switch on the supply.
NOTE: Do not attempt to use or replace the mains adaptor supplied with this product
other than a Geemarc AC/DC adaptor type 09200DG.
NOTE: Do not attempt to use or replace the mains adaptor supplied with this product
other than a Geemarc AC/DC adaptor type 09200DG.
Connect the line cord
Connect the small plug on the line cord into the Line Cord In socket. Connect other end
of line cord into the telephone socket. To connect a telephone to your Clearview
Cordless Caller Display base unit, plug the telephone line cord into the spare socket of
the doubler at the end of the Clearview line cord. Should you not have a modular
telephone socket as shown, please contact your local British Telecom or other Network
Operator.
Setting up the base unit
1. Press Set for 5 seconds until you see “OPTI”.
2. Press Page for language setting. Press Set to select “ENG” (English), “SVE”
(Swedish), “DAN” (Danish), “SUO” (Finnish).
3. Press Page again to show “TIME”. Press Page twice, the date and time setting
will be automatically updated each time you receive a call.
Setting up the display unit
Insert Batteries to Clearview Cordless Caller Display
Open the battery compartment on the underside of your Clearview Cordless Caller
Display by pushing it towards the back edge. You will need 4 x AA alkaline batteries
(NOT INCLUDED).
WARNING - Calls list back up time is 1 minute. Do not
remove all batteries or the stored memories may be lost. To
ensure the memories are not lost users should take out one
battery at a time and replace with a new one before taking out
the next battery. Change all 4 batteries when the battery low
symbol shows in the display.
NOTE - The directory memory is non volatile and will not be
lost when changing batteries.
Operation
Setting Clearview Cordless Caller Display identification (ID) code
The Clearview Display must be set with the same identification (ID) code as the base.
The Clearview display will read “SET CODE” after inserting the four AA alkaline
batteries.
1. Place Clearview display next to base.
2. On the Clearview display, press Learn. The display will read “LEARN”.
3. On the base, press Page within 10 seconds. This sends the base ID code to the
Clearview display.
To indicate that the ID code has been properly set, the Clearview will beep and its
display will read “ID SET”.
Verifying that the Clearview display is within range of the base
When Page is pressed at the base, if the Clearview display is within range, it will beep
once and the display will show “PAGE RECEIVED” for 30 seconds.
If it does not show “PAGE RECEIVED”, then move the Clearview display closer to
the base and repeat the previous steps. If it still does not beep, repeat the steps above
to verify that the identification code has been properly set.
To view records in
the call list
To delete a record
from the the call list
To delete all records
from the call list
the call list
To delete a record
from the the call list
To delete all records
from the call list
Using the timer
Press Review Forward or Backward to scroll
through the records
When viewing the record, press Delete
through the records
When viewing the record, press Delete
Press Delete for 5 seconds, until you see the
message indicating that there are no total calls
message indicating that there are no total calls
To start or stop the timer, press Timer. After
stop, the timer display will freeze for 5 seconds
stop, the timer display will freeze for 5 seconds
Helpline - 01707 384438
Used to set
and store
information
For moving through the
Directory list, calls list
or between
digits/characters when
entering a number
Used to delete
all of a number
or just part of it
Used to code display
unit, advance digits and
characters in settings
Used to operate
timer and
alarm clock setting
UG/CLEARVIEW CORDLESS Issue 1 09/00