Heatcraft Refrigeration Products Condensing Units H-IM-CU Manuel D’Utilisation

In order to obtain the maximum capacity from a system, and to ensure 

trouble-free operation, it is necessary to balance each and every system.

This is extremely important with any refrigeration system.
The critical value which must be checked is suction superheat.
Suction superheat should be checked at the compressor as follows:

Measure the suction pressure at the suction service valve of the  

 

 

compressor  and  determine  the  saturation  temperature  corresponding  

 

to this pressure from a  “Temperature-Pressure” chart.
Measure the suction temperature of the suction line about one  

 

 

foot back from the compressor using an accurate thermometer.
Subtract the saturated temperature from the actual  

 

 

 

suction line temperature. The difference is superheat.

Too low a suction superheat can result in liquid being returned to the 

compressor. This will cause dilution of the oil and eventual failure of the 

bearings and rings or in the extreme case, valve failure.
Too high a suction superheat will result in excessive discharge temperatures 

which cause a break down of the oil and results in piston ring wear, piston 

and cylinder wall damage.  
It should also be remembered that the system capacity decreases as the 

suction superheat increases.  For maximum system capacity, suction 

superheat should be kept as low as is practical. Copeland mandates a 

minimum superheat of 20˚F at the compressor.  We recommend that the 

superheat at the compressor be between 20˚F and 30˚F.
If adjustments to the suction superheat need to be made, the expansion 

valve at the evaporator should be adjusted.

1.

2.

3.

After the system has been charged and has operated for at least two hours at 

normal operating conditions without any indication of malfunction, it should 

be allowed to operate overnight on automatic controls.  Then a thorough 

recheck of the entire system operation should be made as follows:

Check compressor discharge and suction pressures.    

 

 

If not within system design limits, determine why and   

 

 

take corrective action.
Check liquid line sight glass and expansion valve operation. If    

 

there are indications that more refrigerant is required, leak test    

 

all connections and system components and repair any  

 

 

leaks before adding refrigerant.  
Observe oil level in compressor crankcase sight glass.  Add oil as   

 

necessary to bring level to bottom 1/4 of the sight glass.  
Thermostatic expansion valves must be checked  

 

 

 

for proper superheat settings. Feeler bulbs must be    

 

 

in positive contact with the suction line and should    

 

 

be insulated. Valves set at high superheat will lower    

 

 

refrigeration capacity.  Low superheat promotes  

 

 

 

liquid slugging and compressor bearing washout.
Using suitable instruments, carefully check line voltage and  

 

 

amperage at the compressor terminals. Voltage must be within    

 

10% of that indicated on the condensing unit nameplate.  If high  

 

or low voltage is indicated, notify the power company.   

 

 

If amperage draw is excessive, immediately determine the cause   

 

and take corrective action.  On three phase motor compressors,    

 

check to see that a balanced load is drawn  

 

by each phase.  
The maximum approved settings for high pressure controls on    

 

our air cooled condensing equipment is 425 psig.  On air cooled    

 

systems, check as follows:   

 

Disconnect the fan motors or block the condenser inlet air.  Watch  

 

high pressure gauge for cutout point.  Recheck all safety and  

 

 

operating controls for proper operation and adjust if necessary.  
Check defrost controls for initiation and termination settings, and  

 

length of defrost period.  Set fail safe at length of defrost + 25%. 

 

Example:   

20 minute defrost  + 5 minutes 

 

 

 

=   25 minute fail safe  

Check drain pan for proper drainage.
Check winter head pressure controls for pressure setting.
Check crankcase heater operation if used.
Install instruction card and control system diagram for  

 

 

use of building manager or owner.

a)

b)

c)

d)

e)

f)

g)

h)
i)
j)
k)

All adjustable controls and valves must be field adjusted to meet desired 

operation. There are no factory preset controls or valve adjustments. This 

includes low pressure, high pressure, adjustable head pressure systems 

and expansion valves.

50

70

20

90

35

40

55

20

70

35

30

40

20

55

35

10

30

10

45

25

0

15

0

25

7

-10

15

0

20

1

-20

10

0

12

1

-30

6

0

8

1"Hg.

* Minimum ambient or box temperature anticipated, high pressure control setting: R-22, 360 PSI; R-404A, R-507, 400 PSI

* The standard preset low pressure switch used for pumpdown is set for 15 PSI cut in / 4 PSI cut out and is a good setting for most pumpdown systems

* ZB Scroll compressors should be set for 25 PSI cut in / 17 PSI cut out (R-404A / R-507)