Behringer U-Control UMX250 Manuel D’Utilisation

U-CONTROL UMX250 User Manual

5)  Press the ENTER button on the keyboard to confirm your assignments. 

To discard your assignments either press the CANCEL button or the ASSIGN 

button again. In either case, the ASSIGN LED goes out and the UMX250 quits 

ASSIGN mode.

(6) 

The USER MEMORY button is used to recall the internal memory. 

The internal memory contains all assignment information set in ASSIGN 

mode. Any changes that were made after USER MEMORY selection are 

automatically saved without further user prompts. The USER MEMORY is 

retained even after the unit is switched off.

(7) 

The two OCTAVE SHIFT buttons are preset to shift the keyboard range 

by several octaves up or down. The associated LEDs help you identify the 

current octave setting (see Table 3.1). Since the OCTAVE SHIFT buttons 

can also be assigned to any MIDI controller, we would like to refer you to 

Chapters 4.2.8 and 4.2.9 for detailed information.

(8) 

The eight high-resolution rotary controls R1 – R8 generate continuous 

controller information. They are the controllers that are shown above 

the buttons in the table  

(10)

. All rotary controllers can be assigned to any 

controller in ASSIGN mode.

(9) 

The eight buttons B1 – B8 generate switch controllers. Again, these are 

factory-set functions (see table  

(10)

  on the device). Like the rotary controls 

the buttons can be freely assigned to any controller in ASSIGN mode.

(10) 

The table shows the controller assignment PRESET at the factory.

(11) 

KEYBOARD LEGEND: Informs you about the special functions performed 

by individual keys on the keyboard. The individual elements of the keyboard 

legend are described in detail in Chapter 4  “Operation”.

Shift one octave up or down

LED on

Shift 2 octaves up or down

flashing

Shift 3 octaves up or down

flashing

Reset (all octave shifts 

are reversed)

LED off

Table 3.1: LED activity depending on the OCTAVE SHIFT status

(16)

(12)

(13)

(14)

(15)

Fig. 3.2: Rear panel connectors

(12) 

Use this socket to supply the UMX250 with current from an external power 

supply unit (not included).

(13) 

The USB connector of the UMX250. The connector (type B) on the device 

is connected using the cable supplied to a free slot on the host computer 

(where you will find a type A connector). It is compatible with the USB 1.1 

and USB 2.0 standards.

(14) 

In addition to the connection to the computer, you can use the MIDI OUT 

to connect additional MIDI devices, so that the UMX250 transforms into a 

fully-featured, easily accessible MIDI interface for your host computer.

(15) 

Use the FOOT SWITCH connector to connect a sustain pedal. This port 

is factory-set and assigned to the MIDI parameter “Foot Pedal” (CC 64), 

which represents a switch controller. When the pedal is pressed (and held) 

in normal Play mode, it generates a controller with the value 127. When the 

pedal is released, the controller falls back to 0 (typical piano sustain pedal 

behavior). Apart from that the pedal assignment is the same as the button 

assignment, i.e. you can assign any MIDI controller to it.

(16) 

The POWER switch is used to switch the unit on and off.

In the following, we will explain the operation of the UMX250 in detail. 

Please note the differentiation between buttons (see control elements  

(9)

) 

and keys (control element  

(1)

)! Please do not confuse these!

After power-up the UMX250 is in PLAY mode. You can start playing, modify filter 

sweeps with the rotary controls, determine program changes intuitively, 

realize panorama changes, controlsoft synths, and so on.

4.1.1  The factory memory
The FACTORY MEMORY is the internal memory storing the basic settings of the 

UMX250. The most important feature of the FACTORY MEMORY is the controller 

map described in point  

(10)

. These settings define a number of useful parameters 

and are automatically loaded when the device is switched on.
Assignments that are modified during a session, will be discarded when the unit 

is switched off. In order to save the modified assignments, the UMX250 has been 

provided with a USER MEMORY.

4.1.2  The user memory
Settings that are stored in the USER MEMORY, are stored permanently in the 

internal flash ROM and will be retained even after switching the unit off.
Change to the USER MEMORY by pressing button 6. When you access the 

USER MEMORY for the first time, it stores a copy of the FACTORY MEMORY 

settings. As soon as you make changes to the existing controller map, they are 

stored automatically without your intervention.
The following control element assignments including channel information can be 

permanently stored in the USER MEMORY:

FOOT SWITCH connector

OCTAVE SHIFT button

VOLUME/DATA fader

PITCH BEND wheel

MODULATION wheel

Rotary controls R1 – R8

Buttons B1 – B8