Marantz AV Pre Tuner AV7005 Manuel D’Utilisation
23
Simple version
Advanced version
Information
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
NEDERLANDS
SVENSKA
Basic version
n
AM loop antenna assembly
1
Put the stand section
through the bottom of the
loop antenna from the
rear and bend it forward.
Stand
Square
hole
Projecting
part
Square
hole
Projecting
part
Loop
antenna
2
Insert the projecting part
into the square hole in
the stand.
n
Using the AM loop antenna
Suspending on a wall
Suspend directly on a wall without assembling.
Nail, tack, etc.
Standing alone
Use the procedure shown above to assemble.
NOTE
• Do not connect two FM antennas simultaneously.
• Even if an external AM antenna is used, do not disconnect the AM
• Even if an external AM antenna is used, do not disconnect the AM
loop antenna.
• Make sure the AM loop antenna lead terminals do not touch metal
parts of the panel.
• If the signal has noise interference, connect the ground terminal
(GND) to reduce noise.
• If you are unable to receive a good broadcast signal, we recommend
installing an outdoor antenna. For details, inquire at the retail store
where you purchased the unit.
where you purchased the unit.
Connecting a wireless receiver
(RX101)
By connecting a wireless receiver RX101 (sold separately) to this unit,
you can receive and playback audio signals from other devices using
the Bluetooth Communication Function.
• Use a Bluetooth device that is A2DP compatible (vpage 109
you can receive and playback audio signals from other devices using
the Bluetooth Communication Function.
• Use a Bluetooth device that is A2DP compatible (vpage 109
“A2DP”).
• You can also use wireless receiver RX101 as an external IR receiver.
• For instructions on the wireless receiver settings, refer to the
• For instructions on the wireless receiver settings, refer to the
RX101’s operating instructions.
Wireless receiver RX101
Bluetooth device
(A2DP Compatibility)
Remote control unit
You can enjoy listening to music by connecting a wireless receiver
via the M-XPort input connector. In this case, set the input source to
“M-XPort”.
NOTE
To use wireless receiver RX101 as external IR receiver, set the
remote sensor function of this unit to “Remote Lock:ON” (vpage 89
“Remote control settings”).
remote sensor function of this unit to “Remote Lock:ON” (vpage 89
“Remote control settings”).
Connect a device that has a
multichannel output terminal
• You can connect this unit to an external device fitted with multi-
channel sound audio output jacks to enjoy music and video.
• The video signal can be connected in the same way as a Blu-ray Disc
player / DVD player (vpage 17 “Connecting a Blu-ray Disc player”).
Cables used for connections
Audio cable (sold separately)
Audio cable
(White)
(Red)
R
L
R
L
Audio cable
R
L
R
L
R
L
R
L
R
L
R
L
SUB-
WOOFER
CENTER
SURROUND
BACK
R
L
SURROUND
R
L
FRONT
R
L
AUDIO
Blu-ray Disc player / DVD player /
External decoder
External decoder
To play analog signals input from 7.1CH INPUT terminals, set
“Input Mode” (vpage 71) to “7.1CH IN”.
“7.1CH IN” can also be selected with
“Input Mode” (vpage 71) to “7.1CH IN”.
“7.1CH IN” can also be selected with
A/D
on the remote control
unit.
in Set as Necessary
When a device is connected to the SBL/SBR terminal of 7.1CH INPUT
terminals, set “Amp Assign” (vpage 78) to “Normal”.
terminals, set “Amp Assign” (vpage 78) to “Normal”.
Connecting an antenna
1.AV7005U_ENG.indd 23
2010/08/23 18:32:32