Marantz AV Pre Tuner AV7005 Manuel D’Utilisation

74

ENGLISH

DEUTSCH

FRANÇAIS

ITALIANO

ESPAÑOL

NEDERLANDS

SVENSKA

Dynamic EQ®
Solve the problem of 
deteriorating sound quality 
as volume is decreased 
by taking into account 
human perception and 
room acoustics. Works with 
MultEQ XT.

ON : Use Dynamic EQ. 
OFF : Do not use Dynamic EQ. 

• 

 is displayed when set to “ON”. 

• Buttons on the remote control unit or main unit 

can be used for operations.
Press 

Each time 

 is pressed, the setting is 

changed as shown below.

Dynamic EQ : ON   

Dynamic Volume : Heavy

Dynamic EQ : ON   

Dynamic Volume : Medium

Dynamic EQ : ON   

Dynamic Volume : OFF

Dynamic EQ : OFF   

Dynamic Volume : OFF

Dynamic EQ : ON   

Dynamic Volume : Light

Reference Level Offset
Audyssey Dynamic EQ is 
referenced to the standard 
film mix level. It makes 
adjustments to maintain 
the reference response 
and surround envelopment 
when the volume is turned 
down from 0 dB. However, 
film reference level is not 
always used in music or 
other non-film content. 
Dynamic EQ Reference 
Level Offset provides three 
offsets from the film level 
reference (5 dB, 10 dB, and 
15 dB) that can be selected 
when the mix level of the 
content is not within the 
standard.

0dB  (Film  Ref)  :  This  is  the  default  setting  and  should  be  used  when 
listening to movies. 
5dB : Select this setting for content that has a very wide dynamic range, 
such as classical music. 
10dB : Select this setting for jazz or other music that has a wider dynamic 
range. This setting should also be selected for TV content as that is usually 
mixed at 10 dB below film reference.
15dB : Select this setting for pop/rock music or other program material 
that is mixed at very high listening levels and has a compressed dynamic 
range.

 Setting is enabled when “Dynamic EQ” is “ON” (vpage 74).

Move the cursor 
(Up/Down/Left/Right)

Confirm the setting

Return to previous menu

n

Set MultEQ® XT, Dynamic EQ® and Dynamic Volume®. These can be selected after Audyssey® Auto 
Setup has been performed. For additional information on Audyssey technology, please see page 109.

If you have not performed Auto Setup, or if you change the speaker settings after performing Auto Setup, 
you may not be able to select Dynamic EQ/Dynamic Volume, and “Run Audyssey” may be displayed.
In this case, either perform Audyssey Auto Setup over again or perform “Restore” (vpage 12) to return to 
the settings after Audyssey Auto Setup was run. 

MultEQ XT
Select one equalizer from 
three modes. MultEQ XT  
corrects both time and 
frequency response 
problems in the listening 
area based on Audyssey 
Auto Setup calibration. We 
recommend “Audyssey”.
MultEQ XT is the 
prerequisite function for 
Dynamic EQ and Dynamic 
Volume.

Audyssey : Optimize the frequency response of all speakers. 
Audyssey  Byp.L/R  :  Optimize  frequency  response  of  speakers  except 
front L and R speakers.
Audyssey  Flat  :  Optimize  frequency  response  of  all  speakers  to  flat 
response.
Manual : Apply frequency response set with “Manual EQ” (vpage 76).
OFF : Turn “MultEQ XT” equalizer off.

• “Audyssey”,  “Audyssey  Byp.  L/R”  and  “Audyssey  Flat”  can  be 

selected after Audyssey Auto Setup has been performed. “Audyssey” 
is automatically selected after performing Audyssey Auto Setup. When 
“Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is selected, 

 

illuminates.

• After  running  Audyssey  Auto  Setup,  if  the 

Speaker  Configuration,  Distance,  Channel 
Level, and Crossover Frequency have changed 
without  increasing  the  number  of  speakers 
measured, only 

 illuminates.

• Pressing 

 makes this setting.

• “MultEQ XT” and “Manual” cannot be selected when “EQ Customize” 

is set to “Not Used” (vpage 81).

• When using headphones, “MultEQ XT” is automatically set to “OFF”.

1.AV7005U_ENG.indd   74

2010/08/23   18:33:12