Bunn TF Server DSG2 1/1/5 (W/Count-down Timer)Canada Manuel Du Propriétaire
2
INTRODUCTION
This server is intended for use with a BUNN
®
DUAL
®
TF DBC
®
, SINGLE
®
TF DBC
®
or ICB family brewers.
When proper precautions are followed, 1.0 up to 1.5 gallons of coffee may be brewed directly into the server
and then transported to a remote serving location. The server must be placed on a sturdy counter or shelf.
NOTE: Calibration of the brewer is required prior to the use of the Digital TF Server.
USER NOTICES
The notices on this server should be kept in good condition. Replace unreadable or damaged labels.
DAILY CLEANING
CAUTION: CLEAN AND SANITIZE YOUR SERVER DAILY
NOTE: Bunn-O-Matic recommends the 3 step method for cleaning and sanitizing the server. The 3 step method
consists of hot soapy water using an approved detergent, a fresh water rinse, and an aqueous sanitizing
solution using an approved non-chlorine sanitizer. Do not submerge server.
1. Run a complete brew cycle of just hot water into the server and let it set for a minute. Empty the server
completely by opening the faucet.
2. Remove the sensor assembly, fill server with cleaning solution and thoroughly clean the inside of server.
3. Rinse server thoroughly using fresh water rinse.
4. Fill server with sanitizing solution and let the server set for 5 minutes, then drain through fully open faucet.
3. Rinse server thoroughly using fresh water rinse.
4. Fill server with sanitizing solution and let the server set for 5 minutes, then drain through fully open faucet.
Thoroughly rinse server after sanitizing.
5. Remove the faucet handle/stem assembly by unscrewing the faucet nut just beneath the faucet handle.
6. Use enclosed cleaning brush to thoroughly clean the faucet body and tube.
7. Disassemble the faucet/stem assembly. Thoroughly wash all faucet parts in a mild detergent and water solu-
6. Use enclosed cleaning brush to thoroughly clean the faucet body and tube.
7. Disassemble the faucet/stem assembly. Thoroughly wash all faucet parts in a mild detergent and water solu-
tion. Rinse the parts in hot water. Sanitize the parts for five minutes, thoroughly rinse, then air dry completely.
8. Use enclosed cleaning brush to thoroughly clean the fill tube of the sensor assembly.
NOTE: Never submerge the Digital ThermoFresh
NOTE: Never submerge the Digital ThermoFresh
®
Server Display or sensor assembly in water.
9. Wipe sensor assembly with a clean, damp cloth.
10. Reassemble the faucet and attach it to the dispenser.
11. Wash the entire outside surface of the server and display with a clean damp cloth.
10. Reassemble the faucet and attach it to the dispenser.
11. Wash the entire outside surface of the server and display with a clean damp cloth.
PERIODIC CLEANING
1. Remove the sensor assembly from the server.
2. Remove the two thumb screws and slide display assembly from the server.
3. Wipe the surface of the display unit, area under the display unit, and sensor assembly with a clean damp
2. Remove the two thumb screws and slide display assembly from the server.
3. Wipe the surface of the display unit, area under the display unit, and sensor assembly with a clean damp
cloth.
4.
Wash the entire outside surface of the
sensor assembly
with a mild detergent and water solution and rinse
with hot water. Do not submerse.
NOTE: Thoroughly cleaning the sensor assembly fins will prevent inac-
curate level readings.
5. Replace the display unit and sensor assembly.
43240.11 030912
39043.0000
35710.7000
WARNING
HOT LIQUID
AVERTISSEMENT
LIQUIDE CHAUD
NE PAS IMMERGER
DO N
OT SUBMER
GE
45457.7000
39043.0001
39043.0002