Sony EBS-SP10 Manuel D’Utilisation
SP-TUNE User Manual
5
6. Connect the power source to the Plasma Display (refer to Operating Instructions of the Display).
7. Connect the supplied 12v DC adapter to the SP-TUNE and the power outlet. Note that depending
7. Connect the supplied 12v DC adapter to the SP-TUNE and the power outlet. Note that depending
on pre-programmed settings the SP-TUNE can switch on automatically upon attaching power
supply, or remain in a “sleep” state. In either case LEDs on SP-TUNE will blink for about half a
second, then at least the upper LED should blink periodically (see the “LED functions” section
for details).
supply, or remain in a “sleep” state. In either case LEDs on SP-TUNE will blink for about half a
second, then at least the upper LED should blink periodically (see the “LED functions” section
for details).
8. The subsequent behavior of SP-TUNE depends on its mode of operation (see the “Operating
Modes” chapter). A quick way to test correctness of setup is to use the “Power” key of Sony
remote to switch the “Power” state of SP-TUNE on – (1) when pressing key on remote the upper
LED should blink fast (signaling the IR signal reception); (2) the SP-TUNE and the panel should
switch on, which should be observable on the panel.
remote to switch the “Power” state of SP-TUNE on – (1) when pressing key on remote the upper
LED should blink fast (signaling the IR signal reception); (2) the SP-TUNE and the panel should
switch on, which should be observable on the panel.
5 Sony
Plasma
Settings
The EBS-SP10 (SP TUNE) is designed and tested to work with your Sony plasma monitor to provide TV
Tuner source for flexible use. To experience the best possible image quality, suggested adjustments are
recommended for your Sony plasma monitor.
EBS-SP10 Monitor Selection
Tuner source for flexible use. To experience the best possible image quality, suggested adjustments are
recommended for your Sony plasma monitor.
EBS-SP10 Monitor Selection
The EBS-SP10 has a setting for which Sony Plasma monitor you are using with your TV tuner device.
Enter the menu for the EBS-SP10 and under General Settings, select the correct model of your Sony
plasma monitor.
Enter the menu for the EBS-SP10 and under General Settings, select the correct model of your Sony
plasma monitor.
Plasma Monitor Settings
Using the supplied remote, enter the Display Menu for the Sony monitor and adjust the following
settings:
Using the supplied remote, enter the Display Menu for the Sony monitor and adjust the following
settings:
1) Picture Control Menu:
For best Picture Mode for use of the EBS-SP10 with a Sony monitor, select VIVID mode (default
is STANDARD)
is STANDARD)
2) Custom Setup Menu:
Set RGB Mode to DTV (default is PC)
Screen adjustment (Horizontal / Vertical)
It may be necessary to adjust your display screen for best picture alignment on the first use of the EBS-
SP10 with your Sony display. Using the supplied Sony remote, use the HSIZE, VSIZE, HSHIFT and
VSHIFT buttons and make adjustments using the directional arrows until you fill the screen and align the
image to your preferred setting.
TVs and Displays often "overscan" the image slightly to ensure that difference in channel signals are not
reflected on the screen. You may choose to "overscan" the image and confirm that the image is filled on
the screen for different channels used.
Model Specific Configurations
PFM-50X1
SP10 with your Sony display. Using the supplied Sony remote, use the HSIZE, VSIZE, HSHIFT and
VSHIFT buttons and make adjustments using the directional arrows until you fill the screen and align the
image to your preferred setting.
TVs and Displays often "overscan" the image slightly to ensure that difference in channel signals are not
reflected on the screen. You may choose to "overscan" the image and confirm that the image is filled on
the screen for different channels used.
Model Specific Configurations
PFM-50X1
Null Modem Adapter Required
When using the EBS-SP10 with a Sony PFM-42V1 or PFM-42X1, a Null Modem adapter is
provided for connection on the 9-Pin serial cable. This adapter is required for proper
communication between the EBS-SP10 and the Remote input using an RS232 Cable.
When using the EBS-SP10 with a Sony PFM-42V1 or PFM-42X1, a Null Modem adapter is
provided for connection on the 9-Pin serial cable. This adapter is required for proper
communication between the EBS-SP10 and the Remote input using an RS232 Cable.