Manuel D’UtilisationTable des matièresOn safety1On installation1On servicing1On cleaning1On repacking1On illumination1Unpacking2Projector dimensions2Environment3What about ambient light ?3Which screen type?3What image size? How big should the image be?3Where to install the projector ?3Mounting Configuration3Access to Controls4Opening the top cover4Removing the top cover4Re-installing the top cover4Scan Adaptation4Getting access to the scan switches4Horizontal scan switches4Vertical scan switch4Setting the projector address5Power-up mode5Operational mode5Stand-By mode5Baud Rate for communication with a computer5Password mode5AC Power cord connection6Preparing your power cord6Mains lead with CEE7 plug6Power cord with an ANSI 73.11 plug6AC Power check6AC Input power voltage adaptation6Switching on the projector6Starting up with a full white image6Starting up with "warm up period"6Starting up without "warm up period"6Signal input connection7Connecting a Composite Video source to Port 17Connecting a S-Video (or Composite Video) source to Port 27Connecting a RGB Analog source to Port 37Connecting a RGB Analog source to Port 4/57Connecting a Component Video source to Port 4/57Connecting a RGB Analog source with Tri-level sync to Port 4/5 (option)7Connecting a Component Video source with Tri-level sync to Port 4/5 (option)7Peripheral equipment7Connecting a RCVDS 05 source selector to the projector7Connecting a VS05 source selector to the projector7Connecting an IR Remote Receiver 800 to the projector7Before startin any adjustment8Access to Installation Adjustment Mode8Overview flowchart of the Installation Adjustment Mode8Projector Distance8Optical Lens Focusing8Raster Centering8CRT Projection Angle Adjustment8Taille: 2,1 MoPages: 45Language: EnglishOuvrir le manuel
Manuel D’UtilisationTable des matièresSafety instructions1On safety1On installation1On servicing1On cleaning1On repacking1On illumination1Location and Functions of Control2Rear panel terminology2Front panel terminology2Control panel terminology2a. The Local Keypad2b. RCU control panel terminology2Connections3AC Power (mains) Cord Connection3Power Check3Switching On/Off3Signal Input Connection to the Projector :3Connecting a Composite Video source to port 1.3Connecting a S-Video or Video source to port 2.3Connecting a RGB Analog source to port 3.3Connecting a RGB Analog source to port 4/5.3Connecting a RGB Analog source with Tri-level sync to port 4/5.(option)3Connecting a Component Video source to port 4/5.3Connecting a Component Video source with Tri-level sync to port 4/5.(Opion)3Peripheral equipment3Connecting a RCVDS 05 switcher to the BARCODATA 808S3Connecting a VS05 switcher to the BARCODATA 808S.3Connecting an IR Remote Receiver to the BARCODATA 808S3Controlling4Battery installation in the RCU.4How to use your RCU4Projector Address4How to display a projector address?4How to program an address into the RCU?4Input selection4Analog Picture Controls4Controlling chained projectors.4Start up of the Adjustment Mode5Adjustment Mode5Random Access Adjustment Mode6Starting-Up the Random Access Adjustment mode.6Overview 'Random Access Adjustment' mode6Selecting Setup Pattern6Internal Cross Hatch Pattern6Random access adjustment mode selection menu.6Picture Tuning6Color Balance6Sync Fast/Slow Adjustment6Peaking6Clamp Tuning6Port 2 : Video or S-Video6Line Doubler6Color Select6Focusing6Focusing color select.6Blue on source6Geometry Adjustments6Horizontal Phase Adjustment6Raster Shift Adjustment6Left-Right (east-west) Adjustments6Seagull correction6Left Side Correction6Top-Bottom (north-south) Adjustments6Seagull Correction6Horizontal Size Adjustment6Vertical Linearity Adjustment6Vertical Size Adjustment6Blanking Adjustments6Convergence Adjustment6Service mode7Starting up the Service mode.7Overview flowchart 'Service' mode.7Identification7Copy a block7Deletion of blocks7Deleting block by block7Deletion of all blocks7Change password7Change Language7Run time7Set to midposition7Undo Midposition7Convergence Mid7Undo Convergence Mid(position)7Dynamic Astigmatism (spot shape adjustment)7G2 Adjust7Gamma corrections7CRT run in cycle7Projector Warm Up7CRT Drive Mode7Messages, warnings and failures8Options9Taille: 2,3 MoPages: 57Language: EnglishOuvrir le manuel
