Manuels d'utilisation pour Printronix T4204

Manuel D’Utilisation (English)

Manuel D’Utilisation

Table des matières

Software License Agreement
3
- Definitions.
  3
- License.
  3
Limited Software Product Warranty
4
Communication Notices
5
- Trademark Acknowledgements
  7
- IMPORTANT WARRANTY INFORMATION
  8
1 Introduction
13
- Printronix ThermaLine Help Desk
  13
- Warnings And Special Information
  13
  - Conventions
    14
- The T4204 Label Printer
  14
  - Features
    14
- Thermal Printer Technology
  15
  - The Printing Process
    15
  - Dynamic Print Control
    15
- Media Selection
  16
- Ribbons
  16
- Emulations
  16
  - Hardware Options
    17
  - Bar Code Verification
    18
- Unpacking The Printer
  18
  - Check List
    20
- Printer Installation
  21
2 Operation
25
3 Configuring The Printer
51
- Overview
  51
- Menu Navigation
  51
- Menu Options
  65
  - CONFIG. CONTROL Menu
    65
    - Load Config.
      65
    - Save Config.
      65
    - Print Config.
      66
    - Delete Config.
      66
    - Power-Up Config.
      66
    - Protect Configs.
      66
    - Name Configs
      66
    - Reset Cfg Names
      66
  - Active IGP EMUL Menu
    67
  - Emulation Menu
    68
  - MAINT / MISC Menu
    69
    - Alarm
      70
    - Power-Up State
      70
    - Hex Dump Mode
      70
    - PTX SETUP Option
      70
    - Display Language
      70
    - Reset Cmd CFG Ld
      70
    - Downloaded Fonts
      71
    - File System
      71
    - Cancel Key
      71
    - Auto Locking
      71
    - Set Lock Key
      72
    - Auto Label Map
      73
    - Auto Map Select
      73
    - Compatibility
      76
    - Power Saver Time
      76
  - HOST INTERFACE Menu
    77
    - Auto Switching
      78
      - Port Type
        78
      - Trickle Time
        78
      - Timeout
        79
      - Report Status
        79
    - Centronics (Parallel)
      80
      - Data Bit 8
        80
      - PI Ignored
        80
      - Data Polarity
        80
      - Response Polarity
        81
      - Busy On Strobe
        81
      - Latch Data On
        81
      - Prime Signal
        81
      - TOF Action
        81
      - Buffer Size In K
        81
    - Serial
      82
      - Interface Type
        82
      - Data Protocol
        82
      - Baud Rate
        84
      - Word Length
        84
      - Stop Bits
        84
      - Parity
        84
      - Data Terminal Ready
        85
      - Request to Send
        85
      - Buffer Size In K
        85
      - Poll Character
        85
      - Poll Response
        86
      - Idle Response
        86
      - One Char Enquiry
        86
      - Printer Status
        87
    - IEEE 1284 Parallel (Bidirectional)
      88
      - Prime Signal
        88
      - TOF Action
        88
      - Buffer Size In K
        88
    - Ethernet
      89
      - Buffer Size In K
        89
  - ETHERNET PARAMETERS Menu
    90
  - Printer Control Menu
    91
    - Page Width
      92
    - Page Length
      92
    - Print Speed
      93
    - Print Intensity
      93
    - Print Mode
      93
    - Media Sensor
      93
    - Media Handling
      94
    - Paper Feed Shift
      94
    - Hor Image Shift
      94
    - Ver Image Shift
      94
    - Calibrate
      95
    - Tear-Strip Time
      96
    - Clip Page
      96
    - Error Recovery
      96
  - Font Memory Menu
    97
    - Activating Font Memory Options
      98
    - Max Char Memory
      98
    - Max Cache Memory
      98
    - Max Cache Size
      99
    - Max Cached Char
      99
    - Max Fonts Loaded
      99
    - Font Weight
      99
    - Installed Fonts
      99
  - DIAGNOSTICS Menu
    100
    - Printer Tests
      100
    - System Memory
      101
    - Print Statistics
      101
- IGP/PGL Emulation
  102
  - IGP/PGL Features
    102
  - Configuring The Emulation With The Control Panel
    103
  - IGP/PGL Submenu
    104
    - Define CR Code (Carriage Return)
      105
    - Define LF Code (Line Feed)
      105
    - Autowrap
      105
    - Select SFCC
      105
    - PI Slew Range
      105
    - CR Edit
      106
    - Select Font
      106
    - Slash 0
      106
    - Autoeject
      106
    - Select LPI
      106
    - Auto Uppercase
      106
    - Skip Command Prefix
      107
    - Power On IGP/PGL
      107
    - Extended Execute Copy
      107
    - Barcode Options
      108
      - UPC Descenders
        108
      - Optimized Ratio
        108
      - Interleaved 2/5 Selection
        108
      - AI 00 Spaces
        109
      - Select SO Char.
        109
    - Host Form Length
      109
    - PGL Normal
      109
    - Do FF at TOF
      110
    - IGP 100 Compatibility
      110
    - Ignore Character
      110
      - Ignore Mode
        110
      - Select Character
        110
    - Error Report
      110
    - IGP/PGL Character Set Menu
      111
- IGP/VGL Emulation
  112
  - IGP/VGL Features
    112
  - Configuring The VGL With The Control Panel
    113
  - IGP/VGL Submenu
    114
    - SFCC & Pwrup
      114
      - SFCC
        114
      - Power Up ^X
        114
      - Power Up ^F
        115
      - Power Up ^PY
        115
    - Page Format
      115
    - Graphics Options
      116
      - Slash 0
        116
      - Ignore Dots
        116
      - Append Rotated
        116
      - Truncate Alpha
        116
      - True Vert 1/10
        117
      - Absorb after ^PY
        117
      - UPC Descenders
        117
      - Rot. Char Size
        117
      - Ignore Spaces
        117
      - Midline PY (includes ^PN)
        117
      - Width Limit
        118
      - Absorb After ^PN
        118
    - Error Handling
      119
      - Error Msgs
        119
      - Error Markers
        119
      - Offpage Errors
        119
      - Barcode Errors
        119
    - Ignore / DB8 Setup
      119
      - Ignore Chars
        120
      - Ignore Ch#1
        120
      - Ignore Ch#2
        120
      - Data Bit 8
        120
    - Resolution
      121
      - Cmd Resolution
        121
      - ^Dnn Dot Slew
        121
      - Var Ratio Barcd
        121
    - Font Options
      121
      - Uniform Fonts
        121
      - Proportional Line Length
        121
    - PI Control
      121
      - Printer PI
        121
      - Host PI
        122
      - Max PI 16
        122
    - IGP/VGL Character Set Menu
      123
- LinePrinter Plus Emulation
  124
  - LinePrinter Plus Submenus
    125
    - Printer Protocol
      126
    - Orientation
      126
    - CPI/LPI Select
      127
    - Font Attributes
      127
      - Typefaces
        127
      - Proportional Spacing
        128
      - Bold Print
        128
      - Italic Print
        128
      - Slash Zero
        128
      - Text Position
        129
      - Plot Attributes
        129
    - Page Format
      130
      - Margins - Logical Form
        130
      - Margins - Physical Page
        131
      - Perforation Skip
        131
      - Forms Length
        131
      - Form Width
        131
      - Host Forms Length
        131
  - LinePrinter Plus P-Series Emulation
    132
    - Control Code 06
      132
    - Control Code 08
      132
    - Define CR Code
      132
    - Auto LF
      133
    - Overstrike
      133
    - Define LF Code
      133
    - Select SFCC
      133
    - EVFU Select
      133
    - Alt. Set 80-9F
      134
    - Character Set
      134
    - SFCC d Command
      134
    - PSeries Dbl High
      134
    - FF Valid at TOF
      134
    - P-Series Character Set Menu
      135
  - LinePrinter Plus P-Series XQ Emulation
    136
    - Control Code 06
      136
    - Define CR Code
      136
    - Auto LF
      136
    - Define LF Code
      137
    - Compressed Print
      137
    - Elong/Alt. Font
      137
    - Gothic Typeface
      137
    - EVFU Select
      137
    - Upper Case Select
      137
    - Slew Relative
      138
  - LinePrinter Plus Serial Matrix Emulation
    139
    - Control Code 06
      139
    - Define CR Code
      139
    - Auto LF
      139
    - Overstrike
      140
    - Define LF Code
      140
    - Printer Select
      140
    - Alternate Set 80-9F
      140
    - Character Set
      140
    - SFCC d Command
      140
    - Serial Matrix Character Set Menu
      141
  - LinePrinter Plus Proprinter XL Emulation
    142
    - Define CR Code
      142
    - Auto LF
      142
    - Define LF Code
      142
    - FF Valid At TOF
      143
    - Character Set
      143
    - 20 CPI Condensed
      143
  - Proprinter XL Character Set Menu
    144
  - LinePrinter Plus Epson FX Emulation
    145
    - Define CR Code
      145
    - Auto LF
      145
    - Define LF Code
      146
    - Printer Select
      146
    - Character Set
      146
    - 20 CPI Condensed
      146
  - LinePrinter Plus Epson FX Character Set Menu
    147
- Coax/Twinax Emulation
  148
  - Standard C/T Interface
    148
  - Simple Protocol Converter
    148
  - Coax Emulation Menu
    150
    - Char Set Select
      151
    - Translation Table
      151
    - Active Char Set
      151
    - PA1
      151
    - PA2
      152
    - Buffer Reprint
      152
    - Device ID
      152
    - SCS Buffer Control
      152
    - Early Print Complete
      152
    - Cancel IGP/DCU
      153
    - PTX Transparent Control
      153
      - Lead-in Chars
        153
      - Alt. Set 80-9F
        153
    - Change Case
      153
    - Set Text Orientation
      153
    - Image Buf Size
      154
    - Intervention Req
      154
    - Compatibility Options
      154
      - CR at MPP+1
        154
      - NL at MPP+1
        154
      - Position Aft FF (4234 only)
        155
      - Last Char = FF
        155
      - Null Suppression
        155
      - FF Validity
        155
      - Auto Skip At End
        155
      - FF After Job
        156
      - CR, EM, And NL (3287 only)
        156
    - Translate Table
      156
    - Host Override
      156
    - Format Control
      157
    - Max. Print Width
      157
    - Buffer Print
      157
  - Twinax Emulation Menu
    158
    - Char Set Select
      159
    - Translation Table
      159
    - Active Char Set
      159
    - Device ID
      159
    - Device Address
      160
    - 5225 World Trade
      160
    - Cancel IGP/DCU
      160
    - PTX Transparent
      160
      - Lead-in Char.
        160
      - Alt. Set 80-9F
        160
    - Graphic Chek Err
      161
    - Graphic Chek Code
      161
    - LAC Option
      161
    - LAC Approx.
      161
    - Set Text Orientn
      161
    - Host Override
      162
    - Format Control
      162
    - Max. Print Width
      162
    - Buffer Print
      162
  - SPC Coax Params
    163
    - SPC Type
      163
    - Logical Buff Size
      163
    - Image Buff Size
      163
    - Intervention Req
      163
    - Buffer Print
      164
    - Translation Tbl
      164
    - PA1
      164
    - PA2
      164
    - Buffer Reprint
      164
    - SPC Null Suppression
      164
    - NL at MPP+1
      164
  - SPC Twx Params
    165
    - Device Address
      165
    - SPC Type
      166
      - Printer Type
        166
      - SFCC Char
        166
      - EVFU
        166
      - SPC Char Set
        166
    - Translation Table
      166
    - Buffer Print
      166
- Loading Flash Memory
  167
  - Downloading Software To Flash Memory
    167
  - Downloading Optional Font Files To Flash Memory
    170
4 Interfaces
177
- Overview
  177
  - Standard Host Interfaces:
    177
  - Optional Host Interfaces:
    177
- Centronics Parallel Interface
  178
  - Centronics Parallel Interface Signals
    179
- IEEE 1284 Parallel Interface
  180
  - Compatibility Mode
    180
  - Nibble Mode
    180
  - Byte Mode
    180
  - Signals
    181
  - Terminating Resistor Configurations
    183
    - Removal And Installation
      184
- RS-232 And RS-422 Serial Interfaces
  185
  - RS-232
    185
  - RS-422
    186
5 Diagnostics And Troubleshooting
187
- Printer Self-Test
  187
  - Printing Test Labels
    187
- Troubleshooting Common Situations
  188
  - Improving Processing Time
    188
  - Data Exchange
    188
    - Handshaking
      188
    - Interfacing
      189
  - Controlling Print Quality
    190
  - Other Printer Problems
    191
  - Printer Alarms
    194
  - Fault Messages
    194
    - Operator-Correctable Fault Messages
      195
    - Fault Messages Requiring Field Service Attention
      195
A Specifications
201
- Printing
  201
- Label/Tag Media Specifications
  203
- Lists Of Approved Media
  204
- Indicators And Switches
  204
- Host Interfacing
  204
- Electrical:
  204
- Memory:
  205
- Environmental:
  205
- Physical:
  205
- Options:
  205
B Printer Options
207
- Hardware Options
  207
- Supplies And Accessories
  209
C Setting The Page Length
213
D ASCII Control Codes
215
E Glossary
219

Manuel D’Utilisation

Taille:

2,9 Mo
Pages:

232
Language:

English

Ouvrir le manuel