Hitachi VM-H100LA Manuale Utente
Getting Started
- 10 -
• Do not leave the camera under warm water. Even if it is less than 3.3 feet (1m) deep, the warm water could
enter the camera and cause it to malfunction.
enter the camera and cause it to malfunction.
To Prevent Condensation
• When the camcorder is moved from a cold place to a warm place, leave it for a while until it reaches the ambient
temperature.
• Be careful that no water droplets or snow flakes enter the camcorder. If they enter, the humidity inside rises and
condensation is likely to occur.
• Moisture also condenses on the lens. If moisture condenses on the lens, clear pictures cannot be recorded.
Wipe off the moisture before using the camera again.
• If moisture condenses on the LCD screen, use the LCD cleaner provided to wipe it off.
temperature.
• Be careful that no water droplets or snow flakes enter the camcorder. If they enter, the humidity inside rises and
condensation is likely to occur.
• Moisture also condenses on the lens. If moisture condenses on the lens, clear pictures cannot be recorded.
Wipe off the moisture before using the camera again.
• If moisture condenses on the LCD screen, use the LCD cleaner provided to wipe it off.
Getting Started
This section guides you through the initial preparation of the camcorder. None of these processes are complex.
Set aside some time, relax, and familiarize yourself with this quality instrument.
Enjoy getting to know all about your Hitachi 8mm camcorder. The more comfortable and familiar you are with the
machine and its features, the more you can make it do for you. Let's get started!
It is crucial that you read and understand all the safety instructions before you begin. If you haven't read the safety
instructions yet, please take time to do so now.
Set aside some time, relax, and familiarize yourself with this quality instrument.
Enjoy getting to know all about your Hitachi 8mm camcorder. The more comfortable and familiar you are with the
machine and its features, the more you can make it do for you. Let's get started!
It is crucial that you read and understand all the safety instructions before you begin. If you haven't read the safety
instructions yet, please take time to do so now.
Charging the Battery
The first step is to set the battery to charge. Once fully charged the battery will give an operating time of
approximately 50 minutes, but this is reduced to a half to one-third depending on how often you use the zoom and
start/stop functions.
Charge the battery at a temperature range of 50ºF (10ºC) - 86ºF (30ºC) to prevent damage to the battery.
approximately 50 minutes, but this is reduced to a half to one-third depending on how often you use the zoom and
start/stop functions.
Charge the battery at a temperature range of 50ºF (10ºC) - 86ºF (30ºC) to prevent damage to the battery.
Using the AC Adapter/Charger
To Charge the Battery Attached to the AC Adapter/Charger
1. Plug the AC adapter/charger power cord into an AC outlet. Make sure that the wide blade fits into the wide slot.
If it doesn't fit try reversing it. If you still cannot make it fit into the outlet either contact an electrician to replace
your obsolete outlet, or use a polarized cord or outlet accessory.
2. Push the battery till it is flush with the AC adapter/charger sliding it in the direction of the arrow as shown in the
figure.
3. The CHARGE light on the AC adapter/charger lights during charging and goes out when charging is finished.
If it doesn't fit try reversing it. If you still cannot make it fit into the outlet either contact an electrician to replace
your obsolete outlet, or use a polarized cord or outlet accessory.
2. Push the battery till it is flush with the AC adapter/charger sliding it in the direction of the arrow as shown in the
figure.
3. The CHARGE light on the AC adapter/charger lights during charging and goes out when charging is finished.
To Charge the Battery Loaded in the Camcorder
You can charge the battery while it is loaded in the camcorder after recording is finished, etc. (Load a battery in
the camcorder. Refer to "Camcorder Battery" on page 17.)
1. Set the CAM/OFF/VIDEO switch of the camcorder to "OFF".
2. Connect the external power cord plug to the DC OUTPUT jack on the AC adapter/charger.
3. Attach the other end of the external power cord to the installation section at the bottom of the camcorder.
the camcorder. Refer to "Camcorder Battery" on page 17.)
1. Set the CAM/OFF/VIDEO switch of the camcorder to "OFF".
2. Connect the external power cord plug to the DC OUTPUT jack on the AC adapter/charger.
3. Attach the other end of the external power cord to the installation section at the bottom of the camcorder.