Johnson Controls PC090 THRU 240 Manuale Utente
430645-YIM-D-0610
2
Johnson Controls Unitary Products
Nomenclature
General
These condensing units are designed for outdoor installation on
a roof or at ground level. Every unit is completely piped and
wired at the factory and is shipped ready for immediate
installation. Only the liquid and suction lines to the evaporator
coil, the filter drier, the thermostat wiring and the main power
wiring are required to complete the installation. Each unit is
dehydrated, evacuated, leak tested and pressure tested at 450
psig before being pressurized with a holding charge of
refrigerant R-410A for shipment and/or storage.
a roof or at ground level. Every unit is completely piped and
wired at the factory and is shipped ready for immediate
installation. Only the liquid and suction lines to the evaporator
coil, the filter drier, the thermostat wiring and the main power
wiring are required to complete the installation. Each unit is
dehydrated, evacuated, leak tested and pressure tested at 450
psig before being pressurized with a holding charge of
refrigerant R-410A for shipment and/or storage.
All controls are located in the front of the unit and are readily
accessible for maintenance, adjustment and service. All wiring
(power and control) can be made through the front of the unit.
accessible for maintenance, adjustment and service. All wiring
(power and control) can be made through the front of the unit.
Product Category
P = Split System, Condenser, HP, R-410A
Product Identifier
C = Standard Efficiency, 2-Pipe, R-410A
D = Standard Efficiency, 4-Pipe, R-410A
D = Standard Efficiency, 4-Pipe, R-410A
Nominal Cooling Capacity - MBH
090 = 7.5 Ton
120 = 10 Ton
150 = 12.5 Ton
180 = 15 Ton
240 = 20 Ton
120 = 10 Ton
150 = 12.5 Ton
180 = 15 Ton
240 = 20 Ton
C00 = Cooling Only
Product Options
AA = None
AB = Phase Monitor
AC = Coil Guard
AE = Phase Monitor + Coil Guard
LA = Low Ambient
LB = Low Ambient + Phase Monitor
LC = Low Ambient + Coil Guard
LD = Low Ambient + Phase Monitor
+ Coil Guard
LE = Low Ambient + Technicoat Cond. Coil
LF = Low Ambient + Technicoat Cond. Coil
+ Phase Monitor
LG = Low Ambient + Technicoat Cond. Coil
+ Coil Guard
LH = Low Ambient + Technicoat Cond. Coil
+ Phase Monitor + Coil Guard
TA = Technicoat Condenser Coil
TB = Technicoat Condenser Coil + Phase
Monitor
TC = Technicoat Condenser Coil + Coil Guard
TE = Technicoat Condenser Coil + Coil Guard
+ Phase Monitor
AB = Phase Monitor
AC = Coil Guard
AE = Phase Monitor + Coil Guard
LA = Low Ambient
LB = Low Ambient + Phase Monitor
LC = Low Ambient + Coil Guard
LD = Low Ambient + Phase Monitor
+ Coil Guard
LE = Low Ambient + Technicoat Cond. Coil
LF = Low Ambient + Technicoat Cond. Coil
+ Phase Monitor
LG = Low Ambient + Technicoat Cond. Coil
+ Coil Guard
LH = Low Ambient + Technicoat Cond. Coil
+ Phase Monitor + Coil Guard
TA = Technicoat Condenser Coil
TB = Technicoat Condenser Coil + Phase
Monitor
TC = Technicoat Condenser Coil + Coil Guard
TE = Technicoat Condenser Coil + Coil Guard
+ Phase Monitor
Installation Options
A = None
2 = 208/230-3-60
4 = 460-3-60
5 = 575-3-60
7 = 380/415-3-50
4 = 460-3-60
5 = 575-3-60
7 = 380/415-3-50
Configured Split Condenser Model Number Nomenclature
A = Standard Motor
Airflow
Product Generation
1 = First Generation
2 = Second Generation
2 = Second Generation
Voltage
Heat Type & Nominal Heat Capacity
P C 240 C00 A 2 A AA 2 A
Product Style
A = Style A
2 = Non Pwr’d Conv Outlet
1 = Disconnect
T = Options 1 & 5
S = Options 5
D = Options 1 & 2
C = Option 2
B = Option 1
Options
5 = Pwr’d Conv Outlet
This Split-System (Air Condensing / Heat Pump / Air
Handling) unit is one component of an entire system. As
such it requires specific application considerations with
regard to the rest of the system (air handling unit, duct
design, condensing unit, refrigerant piping and control
scheme).
Handling) unit is one component of an entire system. As
such it requires specific application considerations with
regard to the rest of the system (air handling unit, duct
design, condensing unit, refrigerant piping and control
scheme).
Failure to properly apply this equipment with the rest of
the system may result in premature failure and/or
reduced performance / increased costs. Warranty
coverage specifically excludes failures due to improper
application and Unitary Products specifically disclaims
any liability resulting from improper application.
the system may result in premature failure and/or
reduced performance / increased costs. Warranty
coverage specifically excludes failures due to improper
application and Unitary Products specifically disclaims
any liability resulting from improper application.
Please refer to the equipment Technical Guide,
Installation Manual and the piping applications bulletin
247077 or call the applications department for Unitary
Products @ 1-877-UPG-SERV for guidance.
Installation Manual and the piping applications bulletin
247077 or call the applications department for Unitary
Products @ 1-877-UPG-SERV for guidance.