M&S Systems NR8M Dépliant
Step 1 Determine speaker location and mark your plans for future
reference. These speakers DO NOT use mounting rings. Cut
a 9 3/8" diameter hole in the ceiling for the speaker. Each
speaker should be mounted at least 2' from the walls if ceiling
mounted or at least 2' from the ceiling if wall mounted.
DO NOT mount speakers in outside walls.
a 9 3/8" diameter hole in the ceiling for the speaker. Each
speaker should be mounted at least 2' from the walls if ceiling
mounted or at least 2' from the ceiling if wall mounted.
DO NOT mount speakers in outside walls.
Step 2 Remove the red & black wire pigtail (some speakers may be
supplied with wires soldered to the terminals which should
not be removed) from the speaker terminals and connect to
the red & black (or Blue & Violet) wires from the speaker wire
using wire nuts. Be sure that the red(blue) wire (+) is connect-
ed to the red(blue) (+)pigtail lead and that the black(violet)
wire (-) is connected to the black(violet) (-) pigtail lead as
shown in figure 1. Reconnect the slip-on connectors to the
speaker terminals. Note that one terminal is larger than the
other to insure proper phasing.
not be removed) from the speaker terminals and connect to
the red & black (or Blue & Violet) wires from the speaker wire
using wire nuts. Be sure that the red(blue) wire (+) is connect-
ed to the red(blue) (+)pigtail lead and that the black(violet)
wire (-) is connected to the black(violet) (-) pigtail lead as
shown in figure 1. Reconnect the slip-on connectors to the
speaker terminals. Note that one terminal is larger than the
other to insure proper phasing.
Step 3 Remove grill cover from speaker. Use four screws provided to
fasten speaker to the opening in ceiling. Install the speaker in
the ceiling opening, as shown in figure 2. Turn the mounting
clamp screws clockwise until the speaker is secure. DO NOT
OVER TIGHTEN the screws. This can damage the speaker
and/or the ceiling material and make the metal grill difficult
to install.
the ceiling opening, as shown in figure 2. Turn the mounting
clamp screws clockwise until the speaker is secure. DO NOT
OVER TIGHTEN the screws. This can damage the speaker
and/or the ceiling material and make the metal grill difficult
to install.
Step 4 Divide each adhesive bead strip in half. (Adhesive bead strips
are in clear plastic self closing bag). Place strips on edge of
grill as shown in figure 2. Reinstall grill on speaker.
grill as shown in figure 2. Reinstall grill on speaker.
INSTALLATION FOR EXISTING CONSTRUCTION OR TRIM OUT OF NEW CONSTRUCTION:
Plastic clamping ears shown in
the install position (4 places)
Red (Blue) wire
Connect to
16 Gauge 2 conductor
wire from wall plate
or volume control
Black (Violet) wire
Mounting Screws
Ceiling Material
Metal Grill
Adhesive Bead Strip
4 Places
NR8M Speaker
FIGURE 1
FIGURE 2
M&S SYSTEMS 2-YEAR LIMITED WARRANTY
M&S Systems, Inc. warrants for two years (2) all products to be free of factory-caused
defects in material and workmanship. M&S Systems, Inc. will repair or replace, at
its option, parts and materials at no charge, regardless of the problem. This war-
ranty extends to the original purchaser of the product and to each subsequent
owner of the product during the term of this warranty. This warranty covers only the
liability described above, and does not include liability for incidental or consequential
damages. NOTE: Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
defects in material and workmanship. M&S Systems, Inc. will repair or replace, at
its option, parts and materials at no charge, regardless of the problem. This war-
ranty extends to the original purchaser of the product and to each subsequent
owner of the product during the term of this warranty. This warranty covers only the
liability described above, and does not include liability for incidental or consequential
damages. NOTE: Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
115811 D
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,NR8M/FMC8 - LINEAR P/N: 115811 D - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500” X 11.000” - SCALE: 1-1 - SIDE 2 OF 2