Audio-Technica ATM710 Dépliant

• Tailored for exacting detail, high-fidelity vocal reproduction with 

maximum impact and intelligibility

• Excels in venues with controlled stage volume or in-ear monitoring

• Cardioid polar pattern reduces pickup of sounds from the sides 

and rear, improving isolation of desired sound source 

• Durable performance for professional applications

• Superior anti-shock engineering for low handling noise 

• Multi-stage grille design offers excellent protection against plosives 

and sibilance without compromising high-frequency clarity 

• Condenser design for studio-quality performance

• Integral 80 Hz HPF switch and 10 dB pad 

• Corrosion-resistant contacts from gold-plated XLRM-type 

connector  

• Rugged, all-metal design and construction for years of trouble-free 

use

The ATM710 is intended for use in professional applications where
remote power is available. It requires 11V to 52V DC phantom
power, which may be provided by a mixer or console, or by a 
separate, in-line source such as the Audio-Technica AT8801 single-
channel or CP8506 four-channel phantom power supplies.

Output from the microphone's XLRM-type connector is low 
impedance (Lo-Z) balanced. The signal appears across Pins 2 and
3; Pin 1 is ground (shield). Output phase is “Pin 2 hot” – positive
acoustic pressure produces positive voltage at Pin 2.

To avoid phase cancellation and poor sound, all mic cables must be
wired consistently: Pin 1-to-Pin 1, etc.

When using the ATM710 in settings with a stage monitor speaker,
the speaker should be located 180° off axis (at rear of the 
microphone). This placement, in conjunction with the microphone's
uniform cardioid pickup pattern, will virtually eliminate the possibility
of undesired audio feedback.

An integral 80 Hz hi-pass filter provides easy switching from a flat
frequency response to a low-end roll-off. The roll-off position reduces
the microphone's sensitivity to popping in close vocal use. It also
reduces the pickup of low-frequency ambient noise (such as traffic,
air-handling systems, etc.), room reverberation and mechanically
coupled vibrations.

The ATM710 is also equipped with a switchable 10 dB pad that 
lowers the microphone's sensitivity, thus providing higher SPL 
capability for flexible use with a wide range of performers and 
system configurations.

Avoid leaving the microphone in the open sun or in areas where
temperatures exceed 110° F (43° C) for extended periods. Extremely
high humidity should also be avoided.

Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224

Audio-Technica Limited, Old Lane, Leeds LS11 8AG England

www.audio-technica.com

P51806     ©2006  Audio-Technica U.S., Inc.    Printed in China

Fixed-charge back plate
permanently polarized condenser

Cardioid 

40-20,000 Hz

80 Hz, 12 dB/octave

–40 dB (10.0 mV) re 1V at 1 Pa*

200 ohms

148 dB SPL, 1 kHz at 1% T.H.D.

DYNAMIC RANGE (typical)

127 dB, 1 kHz at Max SPL

73 dB, 1 kHz at 1 Pa*

PHANTOM POWER REQUIREMENTS 11-52V DC, 3.5 mA typical

Flat, roll-off; 10 dB pad

274 g (9.7 oz)

179.0 mm (7.05") long, 
50.0 mm (1.97") diameter

Integral 3-pin XLRM-type

AT8470 Quiet-Flex

™

stand clamp 

for 

5

/

8

"-27 threaded stands;

5

/

8

"-27 to 

3

/

8

"-16 threaded adapter;

soft protective pouch

†In the interest of standards development, A.T.U.S. offers full details on its test 

methods to other industry professionals on request.

*1 Pascal = 10 dynes/cm

2

= 10 microbars = 94 dB SPL

1

Typical, A-weighted, using Audio Precision System One.

Specifications are subject to change without notice.

8 kHz

SCALE IS 5 DECIBELS PER DIVISION

LEGEND

200 Hz

1 kHz
5 kHz

Frequency in Hertz

LEGEND

12" or more on axis

Roll-off

Response in dB