Intel IA-32 Manuale Utente
8-28 Vol. 3A
ADVANCED PROGRAMMABLE INTERRUPT CONTROLLER (APIC)
8.6.2
Determining IPI Destination
The destination of an IPI can be one, all, or a subset (group) of the processors on the system bus.
The sender of the IPI specifies the destination of an IPI with the following APIC registers and
fields within the registers:
The sender of the IPI specifies the destination of an IPI with the following APIC registers and
fields within the registers:
•
ICR Register — The following fields in the ICR register are used to specify the
destination of an IPI:
destination of an IPI:
— Destination Mode — Selects one of two destination modes (physical or logical).
— Destination Field — In physical destination mode, used to specify the APIC ID of the
destination processor; in logical destination mode, used to specify a message
destination address (MDA) that can be used to select specific processors in clusters.
destination address (MDA) that can be used to select specific processors in clusters.
— Destination Shorthand — A quick method of specifying all processors, all excluding
self, or self as the destination.
— Delivery mode, Lowest Priority — Architecturally specifies that a lowest-priority
arbitration mechanism be used to select a destination processor from a specified group
of processors. The ability of a processor to send a lowest priority IPI is model specific
and should be avoided by BIOS and operating system software.
of processors. The ability of a processor to send a lowest priority IPI is model specific
and should be avoided by BIOS and operating system software.
•
Local destination register (LDR) — Used in conjunction with the logical destination
mode and MDAs to select the destination processors.
mode and MDAs to select the destination processors.
•
Destination format register (DFR) — Used in conjunction with the logical destination
mode and MDAs to select the destination processors.
mode and MDAs to select the destination processors.
How the ICR, LDR, and DFR are used to select an IPI destination depends on the destination
mode used: physical, logical, broadcast/self, or lowest-priority delivery mode. These destination
modes are described in the following sections.
mode used: physical, logical, broadcast/self, or lowest-priority delivery mode. These destination
modes are described in the following sections.
8.6.2.1
Physical Destination Mode
In physical destination mode, the destination processor is specified by its local APIC ID (see
Section 8.4.6, “Local APIC ID”). For Pentium 4 and Intel Xeon processors, either a single desti-
nation (local APIC IDs 00H through FEH) or a broadcast to all APICs (the APIC ID is FFH)
may be specified in physical destination mode.
Section 8.4.6, “Local APIC ID”). For Pentium 4 and Intel Xeon processors, either a single desti-
nation (local APIC IDs 00H through FEH) or a broadcast to all APICs (the APIC ID is FFH)
may be specified in physical destination mode.
A broadcast IPI (bits 28-31 of the MDA are 1's) or I/O subsystem initiated interrupt with lowest
priority delivery mode is not supported in physical destination mode and must not be configured
by software. Also, for any non-broadcast IPI or I/O subsystem initiated interrupt with lowest
priority delivery mode, software must ensure that APICs defined in the interrupt address are
present and enabled to receive interrupts.
priority delivery mode is not supported in physical destination mode and must not be configured
by software. Also, for any non-broadcast IPI or I/O subsystem initiated interrupt with lowest
priority delivery mode, software must ensure that APICs defined in the interrupt address are
present and enabled to receive interrupts.
For the P6 family and Pentium processors, a single destination is specified in physical destina-
tion mode with a local APIC ID of 0H through 0EH, allowing up to 15 local APICs to be
addressed on the APIC bus. A broadcast to all local APICs is specified with 0FH.
tion mode with a local APIC ID of 0H through 0EH, allowing up to 15 local APICs to be
addressed on the APIC bus. A broadcast to all local APICs is specified with 0FH.