Intel IA-32 Manuale Utente
9-20 Vol. 3A
PROCESSOR MANAGEMENT AND INITIALIZATION
9.10
INITIALIZATION AND MODE SWITCHING EXAMPLE
This section provides an initialization and mode switching example that can be incorporated into
an application. This code was originally written to initialize the Intel386 processor, but it will
execute successfully on the Pentium 4, Intel Xeon, P6 family, Pentium, and Intel486 processors.
The code in this example is intended to reside in EPROM and to run following a hardware reset
of the processor. The function of the code is to do the following:
an application. This code was originally written to initialize the Intel386 processor, but it will
execute successfully on the Pentium 4, Intel Xeon, P6 family, Pentium, and Intel486 processors.
The code in this example is intended to reside in EPROM and to run following a hardware reset
of the processor. The function of the code is to do the following:
•
Establish a basic real-address mode operating environment.
•
Load the necessary protected-mode system data structures into RAM.
•
Load the system registers with the necessary pointers to the data structures and the
appropriate flag settings for protected-mode operation.
appropriate flag settings for protected-mode operation.
•
Switch the processor to protected mode.
Figure 9-3 shows the physical memory layout for the processor following a hardware reset and
the starting point of this example. The EPROM that contains the initialization code resides at the
upper end of the processor’s physical memory address range, starting at address FFFFFFFFH
and going down from there. The address of the first instruction to be executed is at FFFFFFF0H,
the default starting address for the processor following a hardware reset.
the starting point of this example. The EPROM that contains the initialization code resides at the
upper end of the processor’s physical memory address range, starting at address FFFFFFFFH
and going down from there. The address of the first instruction to be executed is at FFFFFFF0H,
the default starting address for the processor following a hardware reset.
The main steps carried out in this example are summarized in Table 9-4. The source listing for
the example (with the filename STARTUP.ASM) is given in Example 9-1. The line numbers
given in Table 9-4 refer to the source listing.
the example (with the filename STARTUP.ASM) is given in Example 9-1. The line numbers
given in Table 9-4 refer to the source listing.
The following are some additional notes concerning this example:
•
When the processor is switched into protected mode, the original code segment base-
address value of FFFF0000H (located in the hidden part of the CS register) is retained and
execution continues from the current offset in the EIP register. The processor will thus
continue to execute code in the EPROM until a far jump or call is made to a new code
segment, at which time, the base address in the CS register will be changed.
address value of FFFF0000H (located in the hidden part of the CS register) is retained and
execution continues from the current offset in the EIP register. The processor will thus
continue to execute code in the EPROM until a far jump or call is made to a new code
segment, at which time, the base address in the CS register will be changed.
•
Maskable hardware interrupts are disabled after a hardware reset and should remain
disabled until the necessary interrupt handlers have been installed. The NMI interrupt is
not disabled following a reset. The NMI# pin must thus be inhibited from being asserted
until an NMI handler has been loaded and made available to the processor.
disabled until the necessary interrupt handlers have been installed. The NMI interrupt is
not disabled following a reset. The NMI# pin must thus be inhibited from being asserted
until an NMI handler has been loaded and made available to the processor.
•
The use of a temporary GDT allows simple transfer of tables from the EPROM to
anywhere in the RAM area. A GDT entry is constructed with its base pointing to address 0
and a limit of 4 GBytes. When the DS and ES registers are loaded with this descriptor, the
temporary GDT is no longer needed and can be replaced by the application GDT.
anywhere in the RAM area. A GDT entry is constructed with its base pointing to address 0
and a limit of 4 GBytes. When the DS and ES registers are loaded with this descriptor, the
temporary GDT is no longer needed and can be replaced by the application GDT.
•
This code loads one TSS and no LDTs. If more TSSs exist in the application, they must be
loaded into RAM. If there are LDTs they may be loaded as well.
loaded into RAM. If there are LDTs they may be loaded as well.