Trango Broadband Access5830 Manuale Utente
Basic Configuration via CLI
Trango Broadband Wireless — Access5830 User Manual Rev. F
page 23
AP SYSTEM INFORMATION PARAMETERS AND RELATED COMMANDS
AP Parameter
Description
Related CLI Command
information, along with active
channel, and SUDB information
for the establishment of a link.
channel, and SUDB information
for the establishment of a link.
#>Set baseid 10
AP ID
Informational parameter used to
provide a unique number for each
AP. Useful for AP sector
planning. Please note that AP ID
is not used by the system for SU
authentication.
provide a unique number for each
AP. Useful for AP sector
planning. Please note that AP ID
is not used by the system for SU
authentication.
set apid <apid>
Example:
Example:
#>Set apid 3
Opmode
Current Opmode of radio.
opmode ap [<y>]
This sets radio in Opmode “AP.” To set radio to
Opmode “OFF,” reboot, and access radio via Ethernet
port within the first 30 seconds.
This sets radio in Opmode “AP.” To set radio to
Opmode “OFF,” reboot, and access radio via Ethernet
port within the first 30 seconds.
Default Opmode
Determines the Opmode (“AP”
or “OFF”) of the radio after
reboot/power cycle. When the
parameter is set to “AP,” the
radio will progress into Opmode
“AP” automatically after
reboot/power cycle.
or “OFF”) of the radio after
reboot/power cycle. When the
parameter is set to “AP,” the
radio will progress into Opmode
“AP” automatically after
reboot/power cycle.
set defaultopmode <ap | off>
Example:
Example:
#>set defaultopmode ap
Opmode Start
Determines the amount of time
the radio will remain in Opmode
OFF after reboot before
progressing to the default
Opmode.
the radio will remain in Opmode
OFF after reboot before
progressing to the default
Opmode.
set defaultopmode ap <time (sec)>
Example:
Example:
#>set defaultopmode ap 60
IP
Subnet
Gateway
Subnet
Gateway
IP, Subnet, and Gateway address
of radio.
of radio.
ipconfig [<new ip> <new subnet mask> <new
gateway>]
Example:
gateway>]
Example:
#>ipconfig 10.1.1.2 255.0.0.0 10.1.1.1
TFTPD Status
TFTPD status (on or off).
TFTPD should be turned on to
import file into radio (such as
new firmware). Default is off.
TFTPD will revert to Off after
rebooting.
TFTPD should be turned on to
import file into radio (such as
new firmware). Default is off.
TFTPD will revert to Off after
rebooting.
tftpd [<on | off>]
Service Radius
User specified estimate of the
distance of the furthest SU the
AP will serve. Based on this
information, the AP will
determine the maximum wait
time for an SU to respond to a
poll before it starts to poll the
next one. Note: This parameter
has no effect on the actual
coverage radius of the radio.
distance of the furthest SU the
AP will serve. Based on this
information, the AP will
determine the maximum wait
time for an SU to respond to a
poll before it starts to poll the
next one. Note: This parameter
has no effect on the actual
coverage radius of the radio.
set serviceradius [<ism|unii> <miles>]
Examples:
Examples:
#>set serviceradius ism 5
#>set serviceradius unii 2
#>set serviceradius unii 2
MIR Threshold (On or
Off)
Off)
Enable/Disable the Maximum
Information Rate (MIR)
Threshold.
Information Rate (MIR)
Threshold.
set mir <on | off>