Zanussi ZXS 646 IT Manuale Utente
3
Once the hob has been installed, it is
important to remove any protective materials,
which were put on in the factory.
important to remove any protective materials,
which were put on in the factory.
Hob burners control knobs
The hob burners control knobs are situated on the hob
right hand side. The symbols on the knobs mean that:
right hand side. The symbols on the knobs mean that:
there is no gas supply
there is maximum gas supply
there is minimum gas supply
Lighting the burners
For easier lighting, proceed before putting a
pan on the pan support.
pan on the pan support.
To light a burner, push in the relevant knob and
turn it counterclockwise to "maximum position".
After lighting the flame, keep the knob pushed
down for about 5 seconds. This will allow the
"thermocouple" (Fig. 1, lett. D) to be heated and
the safety device to be switched off, otherwise the
gas supply would be interrupted.
Then, check the flame is regular and adjust it as
required.
If you cannot light the flame even after several
attempts, check the "cap" (Fig. 1, lett. A) and the
"crown" (Fig. 1, lett. B) are in the correct position.
To put the flame out, turn the knob to the symbol .
turn it counterclockwise to "maximum position".
After lighting the flame, keep the knob pushed
down for about 5 seconds. This will allow the
"thermocouple" (Fig. 1, lett. D) to be heated and
the safety device to be switched off, otherwise the
gas supply would be interrupted.
Then, check the flame is regular and adjust it as
required.
If you cannot light the flame even after several
attempts, check the "cap" (Fig. 1, lett. A) and the
"crown" (Fig. 1, lett. B) are in the correct position.
To put the flame out, turn the knob to the symbol .
• Always turn the flame down or put it out before taking
the pans off the burner.
Manual switch-on (in case of interruption of the
electric supply) : approached a flame to the burner
and push in the relevant knob and turn it
counterclockwise to "maximum position".
and push in the relevant knob and turn it
counterclockwise to "maximum position".
Contents
This appliance complies with the following
E.E.C. Directives:
E.E.C. Directives:
- 2006/95 (Low Voltage Directive);
- 2004/108 (Electromagnetical Compatibility Directive);
- 90/396 (Gas Appliances Directive )
- 2004/108 (Electromagnetical Compatibility Directive);
- 90/396 (Gas Appliances Directive )
and subsequent modifications.
MANUFACTURER:
ELECTROLUX ITALIA S.p.A.
C.so Lino Zanussi 30
33080 Porcia (PN) - ITALIA
ELECTROLUX ITALIA S.p.A.
C.so Lino Zanussi 30
33080 Porcia (PN) - ITALIA
For the User
For the Installer
Instruction for the User
A - Burner cap
B - Burner crown
C - Ignition candle
D - Thermocouple
B - Burner crown
C - Ignition candle
D - Thermocouple
Important Safety Information
2
Instruction for the User
3
Cleaning and Maintenance
6
European Guarantee
13
Technical Data
7
Instruction for the Installer
7
Gas connection
8
Electrical Connection
9
Adaptation to different types of gas
10
Building In
11
Possibilities for insertion
12
Fig. 1
FO 0204
Do not keep the control knob pressed for more
than 15 seconds.
If the burner does not light even after 15 seconds,
release the control knob, turn it the “off” position
and wait for at
least one minute before trying to light the burner
again.
than 15 seconds.
If the burner does not light even after 15 seconds,
release the control knob, turn it the “off” position
and wait for at
least one minute before trying to light the burner
again.